15.0 Command descriptions
1 0 1 1 0 0 0 0B0S.M.A.R.T. Enable Operations3
1 0 1 1 0 0 0 0B0S.M.A.R.T. Enable/Disable Attribute Autosave3
1 0 1 1 0 0 0 0B0S.M.A.R.T. Disable Operations3
1 0 0 1 1 0 0 199Sleep*3
1 1 1 0 0 1 1 0E6Sleep3
1 1 0 0 0 1 1 0C6Set Multiple Mode3
1 1 1 1 1 0 0 1F9Set Max Address3
1 1 1 0 1 1 1 1EFSet Features3
1 0 1 0 0 0 1 0A2Service5
0 1 1 1 - - - -7xSeek3
1 1 1 1 0 0 1 0F2Security Unlock2
1 1 1 1 0 0 0 1F1Security Set Password2
1 1 1 1 0 1 0 1F5Security Freeze Lock3
1 1 1 1 0 1 0 0F4Security Erase Unit2
1 1 1 1 0 0 1 1F3Security Erase Prepare3
1 1 1 1 1 0 1 0F6Security Disable Password2
0 0 0 1 - - - -1xRecalibrate3
0 1 0 0 0 0 0 141Read Verify Sectors (no retry)3
0 1 0 0 0 0 0 040Read Verify Sectors (retry)3
0 0 1 0 0 0 0 121Read Sectors (no retry)1
0 0 1 0 0 0 0 020Read Sectors (retry)1
1 1 1 1 1 0 0 0F8Read Native Max Address3
1 1 0 0 0 1 0 0C4Read Multiple1
0 0 1 0 0 0 1 123Read Long (no retry)1
0 0 1 0 0 0 1 022Read Long (retry)1
1 1 0 0 0 1 1 1C7Read DMA Queued5
1 1 0 0 1 0 0 1C9Read DMA (no retry)4
1 1 0 0 1 0 0 0C8Read DMA (retry)4
1 1 1 0 0 1 0 0E4Read Buffer1
0 0 0 0 0 0 0 000NOP3
1 0 0 1 0 0 0 191Initialize Device Parameters3
1 0 0 1 0 1 0 195Idle Immediate*3
1 1 1 0 0 0 0 1E1Idle Immediate3
1 0 0 1 0 1 1 197Idle*3
1 1 1 0 0 0 1 1E3Idle3
1 1 1 0 1 1 0 0ECIdentify Device1
0 1 0 1 0 0 0 050Format Track2
1 1 1 0 0 1 1 1E7Flush Cache3
1 0 0 1 0 0 0 090Execute Device Diagnostic3
1 0 0 1 1 0 0 098Check Power Mode*3
1 1 1 0 0 1 0 1E5Check Power Mode3
Binary Code Bit
7 6 5 4 3 2 1 0
Code
(Hex)
CommandProtocol
Commands marked * are alternate command codes for previously defined commands.
Figure 76. Command set
(1 of 2)
Deskstar 60 GXP Hard disk drive specification
101
To Next Page
Loading...
