Need help?Do you have a question about the IDTECK Star 100R and is the answer not in the manual?
General| Category | Gateway |
|---|---|
| Operating Mode | Standalone or Network |
| Communication | RS-485 |
| Transmission Distance | 1200m (RS-485) |
| Power Supply | 12VDC |
Describes the controller's function as an intelligent PIN & Proximity Single Door Controller.
Lists the primary functionalities and capabilities of the Star 100R / iPASS IP100R.
Details the technical parameters of the device, including CPU, memory, and read range.
Identifies and explains the components of the device's front panel interface.
Lists and illustrates all components included in the product packaging.
Step-by-step guide for mounting the device and preparing the installation site.
Reference table mapping signal wires to their corresponding colors for correct connections.
Configuration guide for enabling Wiegand output for use as a reader.
Connects the unit to a power source, specifying wire colors and polarity.
Details wiring for connecting the door lock in both safe and secure modes.
Explains how to connect an alarm device to the unit's alarm relay.
Instructions for wiring exit buttons and door contact sensors.
How to connect auxiliary inputs and PC via RS-232.
Guides for connecting external auto-dialers and Wiegand readers.
Guides through registering RF cards for access when only cards are used.
Explains how to register RF cards and associated PINs for access.
Process for registering PINs for access without RF cards.
Setup for accessing using either an RF card or a PIN.
Lists the default operational parameters and settings of the unit.
Explains normal mode, opening/exiting doors, and exit button use.
Outlines system response to unauthorized access attempts, including alarms.
Describes Secure Mode and Duress Alarm functionalities.
How to activate the external chime bell manually using the ESC key.
Introduces the process of modifying system settings using command codes.
Provides a quick reference for command codes and their corresponding setting actions.
Guides for adding users via RF card, PIN, or combined methods.
Procedures for removing user access cards and PINs from the system.
Adjusts the duration the door remains unlocked after valid access.
Modifies the duration the alarm is active for access denial or other events.
Sets the alarm duration for invalid keypad entries.
Configures the alarm duration for door contact sensor errors.
Configures alarm duration for AUX input #1, #2, and #3 detection.
Sets a secret password to trigger a duress alarm without unlocking the door.
Configures the alarm duration for duress situations.
Enables modes for opening or closing the door without authentication.
Allows door opening by pressing the ENT key alone.
Disables the quick access mode, reverting to normal entry procedures.
Configures lock control modes and melody sound.
Sets the duration the keypad is locked after multiple incorrect entries.
Sets detection logic (rising/falling edge) for AUX inputs and exit buttons.
Sets detection logic for door contact sensors.
Manages TTL output states and enables/disables keypad ID entry.
Controls chime bell output and sets delay for Secure Mode activation.
Configures the time-out duration for door open events.
Defines the number of invalid attempts before lockout.
Enables tamper alarm and resets the unit to factory defaults.
Procedure to re-initialize the unit using hardware jumpers when card/PIN is lost.
Procedure to re-initialize the unit using wire connections when card/PIN is lost.
Addresses issues where the unit shows activity but fails to read RF cards.
General guidance for resolving system malfunctions and operational errors.
Solves the problem of the unit unexpectedly switching to general mode during configuration.
Addresses issues preventing the addition of new user access credentials.
Handles problems encountered when deleting user access cards or PINs.
Provides steps for managing lost master credentials, including initialization.
Details the initialization process needed when master card/PIN is lost.
Resolves issues related to failed communication between the unit and a PC.
Addresses problems where the keypad does not correctly process RF card numbers.
Solves issues with the keypad buzzer not sounding and the exit button not working.
Diagnoses issues where RF card data is not transferred from the reader to the computer.
Addresses problems with Wiegand communication when connecting external readers.
Resolves issues where the door lock mechanism fails to operate.
Explains how door lock connections differ based on type and operation.
To Next Page
