Important Safety, Compliance and Warranty Information
How to prevent icker in your video
Safe Usage Guidelines for Products
*Read Manual Before Product Use*
The default camera frequency setting is 50Hz, if you encounter the icker problem,
simply use the remote control, get into Menu to adjust camera frequency that match
the electrical frequency of your region.
• Do not open or modify the product except for battery removal and replacement.
• Do not disassemble or attempt to service this product.
• This product is safe under normal and reasonably foreseeable misuse operating conditions.
• If product is operating improperly, contact the authorized reseller.
• Product must be returned to the authorized reseller for any service or repair.
• This is not a Children's Product and is not intended for use by children under 14 years old.
FunTech Innovation Compliance.
FCC Statement
For Product Safety, EMC, RF and Energy information, go to www.funtechinnovation.com/compliance
Maintenance is not required for product compliance.
This product complies with relevant legal requirements for Restriction of Hazardous Substances
(RoHS) and management of waste electronic and electrical equipment (WEEE). For RoHS and WEEE
information, go to www.funtechinnovation.com/compliance
Batteries, electronic and electrical equipment should not be disposed of with household
waste. Wherever possible, they should be segregated and brought to an appropriate
collection point to enable recycling and avoid potential impacts on the environment and
human health. For more information, contact your local authorities or place of purchase.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Warning: Where shielded interface cables or accessories have been provided with the product
or specified additional components or accessories elsewhere defined to be used with the
installation of the product, they must be used in order to ensure compliance with FCC. Changes
or modications to product not expressly approved by Fun Technology Innovation Inc, could void
your right to use or operate your product by the FCC.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: 1) this device may not cause harmful interference, and 2) this device must accept any
interference received, including interference that may cause undesired operation. This equipment
has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy. And, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
IC statement:
CAN ICES003 (B) / NMB003 Class (B)
FunTech Innovation’s Limited Hardware
Product Warranty - A Summary
This device complies with Industry Canada license exempt RSS standard(s) Operation is subject
to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device. Cordless (Radio
Transmitter) products: Section A. RSS310 (27 MHz transmitters and receivers): This Category
II radio communication device complies with Industry Canada Standard RSS310. Section B.
RSS210 (2.4 GHz transmitters or transceivers): This Category I radio communication device
complies with RSS210 of Industry Canada.
FunTech Innovation warrants that its hardware product shall be free from defects in materials and
workmanship for the length of time identied on your product package beginning from the date of
original retail purchase. See for specic warranty information about your product and procedures
to act on a warranty claim.
FunTech Innovation’s entire liability and your exclusive remedy for any breach of warranty shall
be, at FunTech Innovation’s option, to repair or replace a functional equivalent of the product, or
to refund the price paid, it the hardware is returned to the point of purchase or such other place
as FunTech Innovation may direct along with a receipt. Warranty protections are in addition to
rights provided under local consumer laws and may vary among countries. See the full warranty
information to know your consumer rights and the additional protections provided by this product warranty.
To Previous Page
Loading...