PIONEER MAGVEL ADJUSTMENT STEP 1 - 3.3V OUTPUT
Before this step, one side will cut near the center
After this step, both sides will cut but gap is large. Fix this by proceeding to STEP 2
1) Knob starts all the way left.
Press and hold the button.
2) Slide the knob to the middle.
Keep holding on to the button.
3) Slide the knob all the way
back to the left. Keep holding
down the button.
4) Release the button.
When you are done, the PNP3
will reset itself and go through
a sequence of flashing LEDs.
If this step was done correctly,
the 2nd of 12 LED flashes
will be dimmer than the other
flashes. See details next page.
Please repeat this step if the
2nd of 12 LED flashes is still
bright!
1)
LED is
on
PIONEER MAGVEL ADJUSTMENT STEP 2 - PRECISION MODE
This gets rid of the excessive lag on both sides regardless of the CURVE setting.
When done properly, cuts are sharp, the LED flashs on the cut, and you can set
the CURVE dial in the middle for quality video mixing or however else you want.
1) Slide knob all the way right.
Press calibration button > 5 seconds
until the LED starts to flash.
2) Release the calibration button.
Turn RIGHT CUT and LEFT CUT
dials all the way towards the center.
The LED will be off.
3) Adjust RIGHT CUT dial until the ‘
LED flashes on when sound cuts
in and off when sound cuts off.
Check multiple times to confirm.
LED
flash
after 5s
(1)
(4)
*
*
(2)
LED
stops
flashing
*
(3)
*
***Right and left are as
viewed from the front
of the Innofader PNP3
4) Adjust LEFT CUT dial until the ‘
LED flashes on when sound cuts
in and off when sound cuts off.
Check multiple times to confirm.
5) Press the calibration button for
about 1/2 second. The LED will be
on at this point.
6) Release the calibration button.
The LED will then flash a pattern
to indicate all of the settings. See
details next page.
7) Adjust RIGHT CUT dial to
where you get the desired
cut point.
8) Adjust LEFT CUT dial to
where you get the desired
cut point.
LED
is
ON
(5)
(6)
LED
flashes
settings
***Right and left are as
viewed from the front
of the Innofader PNP3
*
*
LED
flashes
at cut
LED
flashes
at cut
PIONEER MAGVEL ADJUSTMENT STEP 2 - PRECISION MODE (continued)
This gets rid of the excessive lag on both sides regardless of the CURVE setting.
When done properly, cuts are sharp, the LED flashs on the cut, and you can set
the CURVE dial in the middle for quality video mixing or however else you want.
Adjust until
LED flashes
at cut
Adjust until
LED flashes
at cut
Press and
hold button
Keep holding
down button
LED is
on
Keep holding
down button
Release finger
from the button
Knob starts
here
2)
Slide to
Center
Slide to
Left
Dim
flash @
t = t2
LED
turns
on
3)
4)
t1
Time
LED Brightness
Off
DIM ON
t2
t3 t4 t5 t6 t7 t8 t9 t10 t11
The 12 LED flash pattern is unchanged by the Cut Point Threshold Adjustment
It will show the 3.3V Output adjustment you did in Step 1:
But now this pattern is immediately followed with a pattern showing how you adjusted
the cut point. Each adjustment is a number 0 (no adjustment) to 255 (max adjustment).
t13 to t20 is for the LEFT CUT and t21 to t28 is for the RIGHT CUT. If both adjustments
are zero, this flash pattern is skipped. So the following shows a LEFT CUT adjustment
of 32 (00100000 in binary) and a RIGHT cut adjustment of 64 (01000000 in binary):
t14
LED Brightness
Off
DIM=1 ON=0
t15
t16
t17 t18 t19 t20 t21
t22
t23
t24
t25 t26 t27 t28
t13
Time
PIONEER MAGVEL ADJUSTMENT STEP 2 - PRECISION MODE (continued)
12 LED FLASH SEQUENCE AFTER PIONEER MAGVEL STEP 1
t12
If you did NOT do the calibration correctly, the LED flash at time t2 will be bright.
Please make sure to redo Step 1 if this happens! Step 2 will NOT work properly
until Step 1 is successfully completed.
t1
Time
LED Brightness
Off
DIM ON
t2 t3 t4 t5 t6 t7 t8 t9 t10 t11 t12
If you did the adjustment correctly, immediately after calibration and every time you
power on the Innofader, you’ll see the following LED flash pattern. Note the DIM LED:
t1
Time
LED Brightness
Off
DIM ON
t2
t3 t4 t5 t6 t7 t8 t9 t10 t11 t12
Press and
hold button
Release finger
from the button
Press the
button
Release finger
from the button
To Next Page
Need help?
General
