EasyManua.ls Logo

innovair SLIM24 - User Manual

innovair SLIM24
185 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Installation and Owner's Manual
High Efficiency Wall Mount System
IMPORTANT NOTE:
Read this manual carefully before installing or operating your new unit.
Make sure to save this manual for future reference.
SLIM24
Hyper Heat
Appearance of unit may vary.

Table of Contents

Questions and Answers

  • L
    Lori EvansAug 7, 2025
    Why is my innovair Air Handler not cooling properly?
    • D
      Donald SmithAug 7, 2025
      If your innovair Air Handler isn't cooling well, it could be due to several reasons. First, ensure the temperature setting is lower than the room temperature. Check if the heat exchanger on either the indoor or outdoor unit is dirty and clean it if necessary. Also, make sure that all doors and windows are closed while the unit is operating to prevent heat from sunlight, and reduce the amount of heat sources in the room. Finally, low refrigerant could be the cause, so check for leaks, re-seal if necessary, and top off the refrigerant.
  • E
    Erica JordanAug 15, 2025
    What to do if my innovair Air Handlers unit is not working?
    • J
      Jeremy CallahanAug 15, 2025
      If your innovair Air Handler isn't working, first, wait for the power to be restored in case of a power failure. If the power is off, turn it on. Check if the fuse is burned out and replace it if needed. If the unit’s 3-minute protection has been activated, wait three minutes after restarting it. Also, ensure the timer is off. If cold air is entering through doors and windows, make sure they are closed during use. If the unit starts and stops frequently, or there is low refrigerant, check for leaks, re-seal if necessary and top off refrigerant.
  • C
    cwilliamsAug 21, 2025
    How to improve cooling performance of innovair Air Handlers?
    • D
      david41Aug 22, 2025
      To improve poor cooling performance of your innovair Air Handlers, start by lowering the temperature setting. If that doesn't work, consider these steps: * Clean the heat exchanger on the indoor or outdoor unit. * Turn the unit off, remove any obstruction from the air inlet or outlet, and then turn it back on. * Close all doors and windows. * Close windows and curtains to reduce heat from sunlight. * Reduce the number of heat sources in the room. * Check for refrigerant leaks and add refrigerant if needed.
  • A
    Ashley BrowningAug 29, 2025
    What to do if innovair SLIM24 unit is not working because of system circuit blockage?
    • S
      Steven Martinez DDSAug 29, 2025
      If your innovair Air Handlers unit is not working, it might be due to a system circuit blockage. In this case, you should determine which circuit is blocked and replace the malfunctioning piece of equipment.

Summary

Safety Precautions

Precautions

General safety measures and warnings before operation.

Operation and Maintenance

Guidelines for safe unit operation and upkeep.

Information Servicing (Flammable Materials)

Procedures and checks for handling flammable refrigerants.

Model Reference

Model Reference

Identifies indoor/outdoor unit models, capacities, and power supply.

External Appearance

Visual representation of indoor and outdoor unit designs.

Indoor Unit-Air Handler

Feature

Highlights key characteristics and benefits of the indoor unit.

Dimensional Drawings

Technical diagrams showing unit dimensions and measurements.

Part Names

Labels for identifying indoor unit components.

Service Place

Specifies required clearance for indoor unit installation.

Accessories

Lists items included with the indoor unit for installation/operation.

Fan Performance

Charts detailing airflow rates at various static pressures.

Noise Criterion Curves

Data on sound pressure levels across different frequencies.

Electrical Characteristics

Technical data on electrical specifications.

Electrical Wiring Diagrams

Schematics for indoor unit electrical connections.

Outdoor Unit

Dimensional Drawings

Technical diagrams showing outdoor unit dimensions.

Service Place

Specifies required clearance for outdoor unit installation.

Capacity Correction Factor for Height Difference

Tables for capacity adjustment based on elevation.

Noise Criterion Curves

Data on sound pressure levels for outdoor units.

Refrigerant Cycle Diagrams

Illustrates the refrigerant flow within the system.

Electrical Wiring Diagrams

Schematics for outdoor unit electrical connections.

Installation

Installation Overview

General visual guide to the installation process.

Location Selection

Criteria for choosing an appropriate installation site.

Indoor Unit Installation

Step-by-step guide for indoor unit setup.

Outdoor Unit Installation

Step-by-step guide for outdoor unit setup.

Drainage Pipe Installation

Instructions for installing and maintaining drainage pipes.

Duct Work

Guidelines for proper air duct system installation.

Refrigerant Pipe Installation

Procedures for connecting refrigerant piping.

Vacuum Drying and Leakage Checking

Methods for system evacuation and leak testing.

Additional Refrigerant Charge

Process for adding refrigerant as needed.

Engineering of Insulation

Requirements for insulating refrigerant pipes.

Engineering of Electrical Wiring

Standards and practices for electrical wiring.

Test Operation

Steps to verify system functionality post-installation.

Maintenance

First Time Installation Check

Procedures for initial system checks.

Refrigerant Recharge

Steps for recharging the system with refrigerant.

Re-Installation

Instructions for uninstalling and reinstalling components.

Product Features

Display Function

Explains unit display indicators and operational modes.

Safety Features

Details internal safety mechanisms of the unit.

Basic Functions

Describes core operational modes like Fan, Cooling, Heating.

Remote Controller Functions

Explains the operation of the wired remote controller.

Troubleshooting

Safety Caution

Safety guidelines specific to troubleshooting procedures.

General Troubleshooting

Common error codes and solutions for indoor units.

Outdoor Unit Point Check Function

How to check outdoor unit status and codes.

Information Inquiry

Accessing operational data and system settings.

Error Diagnosis and Troubleshooting Without Error Code

Addresses issues without specific error codes.

Quick Maintenance by Error Code

Maps error codes to potential faulty parts.

Troubleshooting by Error Code

Detailed diagnosis for specific error codes.

Check Procedures

General checks for sensors and compressor.

Appendix

Temperature Sensor Resistance Value Table for T1, T2, T3, and T4 (°C - K)

Provides resistance values for key temperature sensors.

Temperature Sensor Resistance Value Table for TP (for some units)(°C -K)

Resistance values for the TP sensor.

Pressure On Service Port

Tables and charts for service port pressure readings.

innovair SLIM24 Specifications

General IconGeneral
Brandinnovair
ModelSLIM24
CategoryAir Handlers
LanguageEnglish