Innovate Motorsports LC-1 User Manual (English)

Other manuals for Innovate Motorsports LC-1

Quick Start Guide2 pages

Need help?

Do you have a question about the Innovate Motorsports LC-1 and is the answer not in the manual?

Innovate Motorsports LC-1 Specifications

General

Brand	Innovate Motorsports
Model	LC-1
Category	Controller
Language	English

Summary

1 Overview

2 Mounting and Connecting the LC-1

2.1 Indicator LED and Calibration button hookup

Details how to connect an LED and a button for status monitoring and calibration.

2.2 Connecting the LC-1 to an external analog AFR display

Explains how to connect the LC-1 to an external analog AFR display.

2.3 Connecting the LC-1 to an ECU or data logger

Guides on connecting the LC-1 to an ECU or data logger for data logging.

2.4 Mounting the sensor using a Bung

Describes the preferred method for mounting the O² sensor using a bung.

2.5 How to fabricate a copper heat sink

Provides instructions for creating a DIY copper heat sink for the sensor.

4 Calibration

4.1 Free air calibration

Explains the process and importance of calibrating the sensor in free air.

4.2 Sensor heater calibration

Details the process for recalibrating the sensor heater circuit.

4.3 Calibration Schedule

Outlines the recommended schedule for performing calibrations.

5 Remote display and recording of Lambda and/or AFR

5.1 Analog Lambda/AFR instrument

Discusses using analog displays with the LC-1 for remote monitoring.

5.2 Digital XD-1 Instrument

Explains how to connect the LC-1 to a digital XD-1 instrument.

5.3 Laptop recording of AFR or Lambda

Details how to record AFR or Lambda data using a laptop.

5.4 Multi channel AFR recording with multiple LC-1's and/or LM-1

Describes setting up multi-channel recording with multiple LC-1 units.

6 Programming the LC-1

6.1 Installing the LM Programmer Software

Guides on installing the necessary software for programming the LC-1.

6.2 Hooking up the LC-1 device to the computer

Explains how to connect the LC-1 to a computer for programming.

6.3 Resetting the calibration data

Details how to reset calibration data on the LC-1.

6.4 Updating the Firmware

Provides instructions for updating the LC-1's firmware.

6.5 Programming the analog outputs

Explains how to configure the analog output characteristics.

6.5.1 Advanced output programming

Covers advanced settings for analog output configuration.

7 Tips, Tricks and Troubleshooting

7.1 General measurement requirements

Discusses general requirements for accurate air-fuel ratio measurements.

7.2 Vehicles with 'smog-pumps'

Addresses specific considerations for vehicles equipped with smog-pumps.

7.3 Measuring at the tail-pipe

Provides guidance on taking measurements at the tail-pipe.

7.4 Single Cylinder Engines

Discusses challenges and tips for single-cylinder engines.

7.5 Diesel Engines

Mentions considerations for using the LC-1 with diesel engines.

7.6 Reference cell or Pump cell circuit open or shorted errors

Describes errors related to reference or pump cell circuits.

7.7 Sensor Timing Errors

Explains sensor timing errors and their causes/solutions.

7.8 Analog Output tricks/hints

Offers tips and tricks for using the analog outputs.

8 Advanced Topics

8.1 Connecting the LC-1 to simulate a narrow band oxygen sensor

Details how to simulate a narrow band oxygen sensor for EFI systems.

Appendix A: LC-1 Cable Pinouts

A1. Sensor Interface Connector (Standard DIN-5 female)

Describes the pinout for the sensor interface connector.

Appendix B: LED blinking codes

Error indication details

Explains how to interpret LED blinking codes for error indications.

Innovate Motorsports LC-1 User Manual

Table of Contents