Inovance MD380-5T5.5GB - Use of DO Terminals; Use of AI Terminals

MD380 User Manual Operation, Display and Application Example
- 73 -
4.11 Use of DO Terminals
7KHFRQWUROERDUGSURYLGHVWKUHH'2WHUPLQDOVQDPHO\)0'2DQG7$7%7&)0DQG
'2DUHWUDQVLVWRURXWSXWVDQGFDQGULYH9'&ORZYROWDJHFLUFXLW7$7%7&LVUHOD\
output, and can drive 250 VAC control circuit.
<RXFDQREWDLQDQRWKHUWZRWHUPLQDOV'2DQG3$3%3&E\LQVWDOOLQJDQ,2H[WHQVLRQ
FDUG'2LVWUDQVLVWRURXWSXWDQG3$3%3&LVUHOD\RXWSXW
<RXFDQGH¿QHWKHIXQFWLRQRIWKH'2WHUPLQDOVE\VHWWLQJ)DQG)WRLQGLFDWHWKH
UXQQLQJVWDWHDQGDODUPLQIRUPDWLRQRIWKH$&GULYH7KHUHDUHDWRWDORIIXQFWLRQV)RU
GHWDLOVVHHWKHGHVFULSWLRQVRIJURXS)
Terminal Corresponding )unction Code Output )eature Description
)M-CME
)5-06 when )5-00 = 0
Tr
ansistor, able to output high-speed pulses 10 Hz
to 100 kHz; drive capacity: 24 VDC, 50 mA
)5-01 when )5-00 = 1 Transistor; drive capacity: 24 VDC, 50 mA
TA
-T%-TC )5-02 Relay; drive capacity: 250 VAC, 3 A
PA
-P%-PC )5-03 Extension card, relay; drive capacity: 250 VAC, 3 A
DO1-CME )5-04 Tr
ansistor; drive capacity: 24 VDC, 50 mA
DO2-CME )5-05
Extension card, transistor; drive capacity: 24 VDC,
50 mA
:KHQ) WKH)0WHUPLQDOLVKLJKVSHHGSXOVHRXWSXW7KHIUHTXHQF\RIRXWSXW
pulses indicates the value of the internal running parameters. The greater the value is, the
higher the output pulse frequency is. The 100% value corresponds to 100 kHz. The property
RIWKHLQGLFDWHGLQWHUQDOSDUDPHWHULVGH¿QHGE\)
4.12 Use of AI Terminals
The AC drive supports a total of three AI terminals, among which AI1 and AI2 are provided
on the control board and AI3 is provided on the extension card.
Terminal Input Signal Characteristic
AI1-GND It receives the signal of 0–10 VDC.
AI2-GND If J8 is connected to the position with "V" mark, it receives the signal of 0–10 VDC.
If J8 is connected to the position with "I" mark, it receives the signal of 4–20 mA.
AI3-GND It is provided on the extension card and receives the signal of -10 to +10 VDC.
As external voltage/current signal, AI is used for frequency source setting, torque setting,
YROWDJHVHWWLQJDW9)VHSDUDWLRQDQG3,'VHWWLQJRUIHHGEDFN7KHFRUUHVSRQGLQJUHODWLRQVKLS
RIWKHYROWDJHRUFXUUHQWDQGDFWXDOVHWWLQJRUIHHGEDFNLVGH¿QHGE\)WR)
efesotomasyon.com