V3 ENGLISH 16-0548
FEATURES
• Press once to turn the plug on or o
• Lights up when the Smart Plug is on and
electricity is owing through it
• Flashing green: searching for/disconnected from
a WiFi network
• Solid green: connected to a WiFi network and
plug is on
• No LED: outlet is o or LED has been disabled in
the app
SAFETY INFORMATION
• Plug directly into an electric outlet (not into an extension cord)
• For indoor use only
• Remove the Smart Plug from the outlet before cleaning
• Keep children away from the Smart Plug and the outlet
• Test the device locally for safe operation before attempting to control it
remotely
• DO NOT use with medical or life support equipment.
• DO NOT clean with liquid
• DO NOT remove the ground pin (middle pin)
• DO NOT use in wet or damp areas
• DO NOT exceed the recommended electrical ratings
• DO NOT use in precision timing applications where inaccurate timing
could be dangerous, such as sunlamps or saunas.
• DO NOT use with devices that should not be operated unattended
• DO NOT use with an outlet controlled by a wall switch as the switch may
be turned o
• Operating ambient temperature: 0° to 40°
LEGAL NOTICES
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
Any changes or modications not expressly approved by the grantee of this device could void the user's authority to
operate the equipment.
FCC Caution
Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to
operate this equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, maybe cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent form that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada Compliance
IC Statement
This device complies with Industry Canada’s licence exempt RSSs. Operation is subject to the following
two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation
of the device.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator and
your body.
ONEYEAR LIMITED WARRANTY
Visit www.insigniaproducts.com for details.
CONTACT INSIGNIA:
1-877-467-4289 (U.S. and Canada) • 01-800-926-3000 (Mexico)
www.insigniaproducts.com
Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a
service mark of Apple Inc.
Google Play and the Google Play logo are trademarks of Google Inc.
INSIGNIA is a trademark of Best Buy and its aliated companies
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2016 Best Buy. All rights reserved.
Made in China
Power button
Power & WiFi status
indicators
The app or WiFi
cannot nd the
Smart Plug.
I can’t nd the
app.
I can’t turn
devices on or o
with the app.
I can't congure
the Smart Plug
LED does not
turn On.
How do I do a
Factory Reset?
• Make sure that your mobile device and the Smart Plug are connected to the same
WiFi network and your network is working properly.
• Reset your Smart Plug. Press and hold for 10 seconds (LED will ash green and
the Smart Plug will reset upon release).
Get the app from the Apple App store or Google Playstore. Your device must have
iOS 9 or later or Android 6.0.1 Marshmallow or later.
• Make sure the devices you connected to the Smart Plug are set to the on position.
• Make sure your mobile device and the Smart Plug are connected to the same
WiFi network.
Press and hold for 10 seconds to reset (LED ashes green and the Smart Plug resets
upon release). Use the app to recongure network settings.
Make sure the LED is not deactivated in the app
Unplug the Smart Plug, then press and hold the power button. Continue holding the
button, plug the Smart Plug into an outlet, then release the button when you hear a
click (about 4 seconds). The LED will be solid.
TROUBLESHOOTING
Problem Solution
NS-SP1X7_16-0548_QSG_V3_EN_Final.ai 2 8/22/2016 9:59:41 AMNS-SP1X7_16-0548_QSG_V3_EN_Final.ai 2 8/22/2016 9:59:41 AM
To Previous Page
Loading...
Need help?
General