Regulatory Information
FCC Supplier's Declaration of Conformity
iRobot Corporation Roomba Model: RVD-Yl, ADJ-Nl
Contains FCC
ID:
UFE-AXFYl
and
contains
IC:
6652A-AXFY1
This
device complies with
part
l 5
of
the FCC
Rules
and
CAN ICES-003(8) /
NMB-003(8).
Operation
is subject
to
the following
two
conditions:
(l)
This
device
may
not
cause harmful interference,
and
(2)
This
device must
accept
any interference received, including interference
that
may
cause undesired operation.
This
device complies with Industry
Canada
license-exempt
RSS
standard(s).
Operation
is subject
to
the following
two
conditions:
(
l)
This
device
may
not
cause interference,
and
(2)
This
device must
accept
any interference, including interference
that
may
cause undesired
operation
of
the device.
•
Changes
or
modifications
not
expressly
approved
by
iRobot
Corporation
could
void the user's authority
to
operate
the
equipment.
•
This
equipment
has been tested
and
found
to
comply
with the limits for a
Class B
digital
device, pursuant
to
part
15
of
the
FCC
Rules
as well as ICES-
003
Rules.
These limits
are
designed
to
provide reasonable
protection
against
harmful interference in a residential installation.
This
equipment
generates,
uses
and
can
radiate
radio
frequency energy and,
if
not
installed
and
used
in
accordance
with the instructions,
may
cause harmful interference
to
radio
communications
. However, there
is
no
guarantee
that
interference
to
radio
communication
will not
occur
in a
particular
installation. If this
equipment
does cause harmful interference
to
radio
or
television reception, which
can
be
determined
by turning
the
equipment
off
and
on, the user
is
encouraged
to
try
to
correct
the interference by one
or
more
of
the
following measures:
• Reorient
or
relocate the receiving antenna.
• Increase
the
separation between the
equipment
and
receiver.
•
Connect
the
equipment
into
an
outlet
on
a circuit different from
that
to
which the receiver
is
connected.
• Consult the
dealer
or
an
experienced radio/TV
technician
for help.
• Under Industry
Canada
regulations, this
radio
transmitter may only
operate
using
an
antenna
of
a type
and
maximum
(or lesser)
gain
approved
for
the
transmitter
by Industry
Canada.
To
reduce potential
radio
interference
to
other
users,
the
antenna
type
and
its
gain
should be so chosen
that
the equivalent isotropically
radiated
power
(e.i.r.p.)
is
not
more
than
the
necessary
for
successful communication.
• FCC Radiation Exposure Statement:
This
product
complies with FCC
§2.
l
091
(b)
for
mobile
device
RF
exposure limits, set forth for
an
uncontrolled
environment
and
is safe
for
the intended
operation
as described in this
manual.
Per
FCC requirements,
maintain
a distance
of
more
than
8 inches
(20
cm)
between
any
person
and
the host device (Roomba robot).
•
ISED
Radiation Exposure Statement:
This
product
complies with the
Canadian
Standard
RSS-1
02
for
mobile
device
RF
exposure limits, set forth for
an
uncontrolled environment
and
is
safe for the intended
operation
as
described
in this manual.
Per
ISED
requirements,
maintain
a distance
of
more
than
8
inches (20
cm)
between
any
person
and
the robot.
iRobot
Corporation,
8 Crosby Drive, Bedford, MA
01730
USA.
http://global.irobot.com
For
battery
recycling
go
to
call2recycle.org;
or
call l
-800-822-8837
Roomba•
i5+
Safety Guide 5
To Next Page
Loading...
