ITT Goulds Pumps AquaBoost II 3 HP User Manual (English)

Questions and Answers:

M
margaret13Aug 12, 2025
What to do if there is a sensor fault on my ITT Controller?
- J
  Justin LawsonAug 12, 2025
  The ITT Controller won't run if the signal from the sensor is disconnected or out of tolerance. The controller will automatically restart when the signal is within tolerance. Possible causes include a disconnected sensor (ensure it's properly connected), a disconnected sensor cable lead inside the controller (check for loose wires), a broken wire in the sensor cable, a miswired sensor cable (verify correct terminal connections: B=Black, R=Red, W=White), or a failed sensor (measure DC voltage between black and white wires at the sensor connector; it should be between 0.5Vdc and 4.5Vdc). If the fault persists, contact your installer.
R
Robert OconnellAug 16, 2025
What to do if my ITT Controller shows a dry well error?
- J
  Jeffrey ReyesAug 16, 2025
  If the ITT Controller displays a 'Dry Well' fault, it could be due to the water supply level falling below the pump's suction inlet, a plugged suction, a restriction in the pipe between the pump and pressure sensor, or a loss of prime. If the 'DRY RUN RESTART' switch is set to 'CONT.' (Continuous), the controller will automatically restart. If it's set to '5X', the controller will restart 5 times; after the 5th error, a manual reset is needed. If the fault persists, contact your installer.
J
Jillian ValentineAug 20, 2025
What to do if my ITT Controller displays a ground fault?
- J
  James RiveraAug 20, 2025
  If your ITT Controller is showing a ground fault, it won't restart automatically. This can be caused by an electrical failure of the motor, an electrical failure of the wiring between the controller and motor, or miswiring of the motor cable. To clear the fault, turn off the power to the controller, wait 1 minute, and then turn the power back on. If the fault persists, contact your installer.
P
Paul CummingsAug 23, 2025
What to do if my ITT Goulds Pumps AquaBoost II 3 HP Controller shows a short circuit error?
- K
  katelynwelchAug 25, 2025
  If your ITT Controller detects a short circuit while the pump was running, it will try to restart three times before showing the fault. This can be caused by an electrical failure of the motor or wiring between the controller and motor. To clear the fault, turn off the power to the controller, wait 1 minute, and then turn it back on. If the fault persists, contact your installer.
C
Claire Everett PhDAug 28, 2025
What to do if my ITT Controller displays pump or motor bound error?
- R
  rachel64Aug 28, 2025
  If the ITT Controller displays a 'Pump or Motor Bound' fault, it will try to restart the motor three times before displaying the fault. This issue can stem from mechanical binding due to debris in the pump, an electrical failure of the motor, or an incorrect setting of the 'MOTOR OVERLOAD SETTING' switch. To clear the fault, turn off the power to the controller, wait 1 minute, and then turn it back on. If the fault persists, contact your installer.
M
Mary WalkerAug 31, 2025
What to do if my ITT Goulds Pumps AquaBoost II 3 HP Controller shows an open lead fault?
- A
  acostakaylaAug 31, 2025
  If the ITT Controller displays an 'Open Lead' fault, it won't restart automatically. This is caused by a disconnected or broken wire between the controller and motor. To clear the fault, turn off the power to the controller, wait 1 minute and turn the power back on. If the fault persists contact installer.
S
Scott StewartSep 4, 2025
What causes a temperature fault on my ITT Goulds Pumps AquaBoost II 3 HP Controller?
- M
  Megan AshleySep 4, 2025
  The ITT Controller might display a temperature fault due to high (above 122ºF/50ºC) or low (below 0ºF/-18ºC) ambient temperatures. The controller will automatically restart when the temperature returns to an acceptable level. If the fault persists, contact your installer.
M
Melissa GuzmanSep 8, 2025
How to check input voltage on ITT Controller?
- P
  Paul WoodsSep 8, 2025
  To solve low or no input voltage on the ITT Controller, check the input voltage to the controller. Use an AC Voltmeter to measure the voltage between L1 and L2; it should be greater than 190Vac.

ITT Goulds Pumps AquaBoost II 3 HP Specifications

General

Horsepower	3 HP
Maximum Pressure	125 psi
Pump Type	Centrifugal
Switch Type	Pressure Switch
Phase	Single

ITT Goulds Pumps AquaBoost II 3 HP User Manual

Table of Contents

Questions and Answers:

ITT Goulds Pumps AquaBoost II 3 HP Specifications