64
Heat & Filter
Provides access to the heating and filtration
programming.
Water Care
Provides access to the water care program-
ming.
WiFi
Provides access to the Wi-Fi programming.
Lock
Provides access to the locking programming.
Time & Date
Provides access to the time and date program-
ming.
Language
Provides access to the language program-
ming.
Units
Temperature unit of measure. (factory set to
Fº
, degrees Fahrenheit).
Back Button: Tap to go back to the previous menu.
Invert Button: Tap to invert the display image.
Scroll up and down to view the selections available.
QProgramming the Heating Mode
Your Jacuzzi spa is equipped with 3 modes of heating.
An automatic mode called “Auto,” where the spa’s tempera-
ture is maintained at all times. An energy saving heating cycle
called “Econo.” A mode that will only activate the heater during
the daytime called “Day” mode.
Note: The heater will activate when the temperature drops ~2°
from the set temperature.
Indicates that the feature is active. Indicates that the
feature is not active.
Auto
Econo
Day
Filter
2
1
Heat & Filter
From the Settings Menu, tap or to highlight the “Heat
& Filter” menu tab in Orange. Tap
Heat & Filter
to the enter the
menu. The select one of the heating settings.
Auto heating:
When programmed to “Auto,” the spa will maintain the water
temperature to the set temperature. Heating will occur when
necessary.
To select this mode, tap (
) next to the “Auto” icon.
Econo heating:
This is an energy saving heating program that allows the spa to
heat during non-peak hours. When programmed to “Econo,” the
spa will only be allowed to heat the water between 5:00 PM to
7:00 AM every day of the week. The hours cannot be adjusted.
To select this mode, tap (
) next to the “Econo” icon.
Day heating:
When programmed to “Day,” the spa will only be allowed to
heat the water between 7:00 AM to 5:00 PM every day of the
week. The hours cannot be adjusted.
To select this mode, tap (
) next to the “Day” icon.
QProgramming the Primary Filter
To access the “Primary Filter” feature, tap
1
from the “Heat
& Filter” menu, to enter the “Primary Filter” programming.
Auto
Econo
Day
Filter
2
1
Heat & Filter
Start
End
pm
12
12pm
8pm
Primary Filter
During a primary filtration, the circulation pump, CLEARRAY
and ozone unit (if applicable) are activated. The factory default
cycle starts at 12:00 AM and last for 8 hours. If you elect to keep
this setting, then you can skip this section.
In extreme bitter cold weather we recommend you pro-
gram the circulation pump to run 24 hours. Refer to the
“Winterizing” section.
Any time the circulation pump runs outside of a program cycle,
e.g. for heating, that run time will be deducted from the next
primary filter cycle. For example, the primary filter cycle is set
to 8 hours every 24 hours but the circulation pump comes on
for 2 hours to heat the water after the cycle has finished. The
next primary filter cycle will only be for 6 hours not 8 hours.
To change the default cycle:
Start
End
pm
12
12pm
8pm
Primary Filter
When you enter the menu, “Start” and “12” will be highlighted.
Tap or to change the hour in 1-hour increments. To
switch from “AM” to “PM” you must round a 12-Hour period.
Tap to accept the change. Tap
End
to program the end
time for the cycle.
- To set the end time of the cycle, tap the hour number (located
next to “End”).
- Tap the number corresponding to the time to change the
cycle end (see above).
Tap
to confirm and save your changes. Tap to return to
the Heat & Filter Menu. Tap again to return to the Settings Menu.
Summer Logic: In warm weather, the water temperature in the spa
may exceed the set temperature. This condition may occur due to
heat transference from the filter/circulation pump and jets pumps. If
the water temperature is higher than 35°C (95°F) and rises 1 °C (2 °F)
To Next Page
Loading...
