Why does my jobmate Air Compressor pressure relief valve keep opening?
The pressure relief valve on your Jobmate Air Compressor might be opening because the tank pressure has exceeded the normal operating pressure or the pressure switch is stuck. In both cases, the suggested solution is to replace the pressure switch.
What to do if jobmate 58-7992-0 Air Compressor is overheating?
If your Jobmate Air Compressor is overheating, relocate it to an area with cool, dry, and well-circulated air. Also, clean all cooling surfaces of the pump and motor thoroughly, and replace any worn parts, reassembling with new seals.
How to fix excessive starting and stopping of jobmate Air Compressor?
To address excessive starting and stopping of your Jobmate Air Compressor, check fittings for leaks using soapy water, and tighten or reseal any leaking fittings, being careful not to overtighten. Replace any worn parts, reassembling with new seals, and replace any faulty seals. Note that some starting and stopping is normal. If the pressure drops too low, adjust the regulator while using the accessory. Check the air requirement of the accessory. If it is higher than the CFM and pressure supplied by the compressor you need a larger compressor. Most accessories are rated at 25% of actual CFM while running continuously. If the problem persists, consult an electrician.
How to troubleshoot low pressure, not enough air and continuous running jobmate Air Compressor?
To troubleshoot low pressure, insufficient air, or continuous running in your Jobmate Air Compressor, close the valve and decrease usage. Check the air requirement of the accessory. If it is higher than the CFM and pressure supplied by the compressor, you need a larger compressor. Most accessories are rated at 25% of actual CFM while running continuously. Remove and clean or replace the air hose, checking for holes and replacing if necessary. Replace the tank immediately if needed, without attempting repairs. Replace any faulty seals, and replace worn parts, reassembling with new seals.
What to do if my jobmate 58-7992-0 motor will not run?
If your Jobmate Air Compressor motor isn't running, there are several potential causes: * The tank pressure might exceed the preset pressure switch limit. In this case, the motor will start automatically when the tank pressure drops below the kick-in pressure. * The motor overload protection might have been tripped. Allow the motor to cool off; the overload switch will reset automatically, which may take several minutes. * A fuse might be blown, or a circuit breaker tripped. Replace the blown fuse or reset the circuit breaker, ensuring you don't use a fuse or circuit breaker with a higher rating than specified for your circuit branch. A 'Fusetron' Type T fuse is acceptable. * Check for low voltage and discontinue the use of an extension cord. * Disconnect other applications from...
Critical safety alerts covering chemical exposure, rupture risks, and potential physical injuries.
Dangers of tank weakening due to rust, modifications, or exceeding pressure limits.
Hazards from propelled objects or compressed air streams causing eye or head trauma.
Ignition risks from sparks, flammable materials, and exceeding pressure limits.
Potential for permanent hearing damage from prolonged exposure to compressor noise.
General risks from accidental activation, propelled fasteners, and tool misuse.
Dangers of electrocution from water, faulty wiring, or contact with live metal parts.
Hazards from loose clothing or jewelry getting caught in moving parts.
Risks from cutting tools and hot compressor components like pump and manifold.
Daily draining of tank moisture to prevent corrosion and freezing issues.
Proper positioning for cooling and airflow, maintaining clearance from walls.
Fastening the unit and releasing pressure before moving it.
Protecting the air hose and electric cord from damage and regular inspection.
Controls compressor ON/OFF operation, manual and automatic modes.
Prevents over-pressurization by automatically opening at preset levels.
Displays the air pressure level stored within the tank.
Allows adjustment of line pressure to suit the connected tool.
Shows the output pressure after regulation.
Connects air hoses to the regulated outlet pressure.
Procedure for draining condensation from the tank to prevent corrosion.
Daily check of the pressure relief valve for proper function and obstructions.
Method for detecting air leaks in hoses and connections using soapy water.
Instructions for cleaning, draining, and protecting the compressor for long-term storage.
Recommended periodic maintenance tasks, including daily checks.
Issues related to insufficient air pressure or volume and their resolutions.
Diagnosing why the compressor fails to shut off automatically.
Causes and solutions for frequent cycling of the compressor.
Troubleshooting tripping circuit breakers or fuses due to voltage drop or overload.
Identifying causes of overheating and methods for cooling the unit.
Reasons for motor stalling, such as leaks, low voltage, or defective valves.
Causes for the pressure relief valve opening unexpectedly.
Troubleshooting steps when the compressor motor fails to start or run.
Resolving issues with check valves or bleeder valves causing pressure loss.
Problems arising from using extension cords and recommended actions.
General| Power Source | Electric |
|---|---|
| Type | Portable |
| CFM at 90 PSI | 2.6 CFM |
| Voltage | 120 V |
| Tank Capacity | 6 gallons |
To Next Page