M9220-GGx-3 Proportional Electric Spring Return Actuators Installation Guide
4
Accessories
Mounting
The M9220-GGx-3 Proportional Electric Spring Return
Actuators can be easily installed on dampers with
1/2 to 3/4 in. or 12 to 19 mm round shafts, or 3/8 and
1/2 in. or 10, 12, and 14 mm square shafts. An
M9220-600 Jackshaft Coupler Kit is available for 3/4 to
1-1/16 in. or 19 to 27 mm round shafts, or 5/8 and
3/4 in. or 16, 18, and 19 mm square shafts; see Table 1
for more details. If the damper shaft extends less than
3-19/32 in. (91 mm), see the Removable Coupler
section for further instructions. If the damper shaft
extends less than 1-5/32 in. (29 mm), install an
extension recommended by the damper manufacturer.
Table 1: Accessories and Replacement Parts (Order Separately)
Code Number Description
DMPR-KC003
7 in. (178 mm) Blade Pin Extension (without bracket) for Johnson Controls
® direct-mount damper
applications (quantity 5)
Note: Available with damper and may also be ordered separately
M9000-153 Crank arm (quantity 1)
M9000-158 Tandem Mounting Kit used to mount two models of M9210/20 Proportional Electric Spring Return
Actuators (quantity 1)
M9000-170 Remote Mounting Kit, horizontal. Kit includes mounting bracket, M9000-153 Crank Arm, ball joint, and
mounting bolts (quantity 1)
M9000-171 Remote Mounting Kit, vertical. Kit includes mounting bracket, M9000-153 Crank Arm, ball joint, and
mounting bolts (quantity 1)
M9000-200 Commissioning Tool that provides a control signal to drive 24 V On/Off, Floating, Proportional,
and/or Resistive Electric Actuators (quantity 1)
M9000-320 Weather Shield Enclosure - NEMA 3R enclosure for protecting a single M9210/20 actuator from rain,
sleet, or snow (quantity 1)
M9000-400 Jackshaft Linkage Kit. Open-ended design enables clamping onto a jackshaft without requiring
access to the ends of the jackshaft (quantity 1)
M9000-519 Valve linkage for mounting M9220 actuator to 2-1/2 to 6 in. flanged ball valves
M9000-604 Replacement Anti-rotation Bracket Kit (with screws) for M9210-xxx-3 Series Proportional Electric
Spring Return Actuators (quantity 1)
M9200-100 Threaded Conduit Adapter, 1/2 NPSM, for M9210(20) and M(VA)9208 Series Actuators (quantity 5)
M9220-600 1 in. (25 mm) Jackshaft Coupler Kit (with locking clip) for mounting M9210-xxx-3 Series Proportional
Electric Spring Return Actuators on dampers with 3/4 to 1-1/16 in. or 19 to 27 mm round shafts, or
5/8 and 3/4 in. or 16, 18, and 19 mm square shafts (quantity 1)
M9220-601 Replacement Coupler Kit (with locking clip) for mounting M9210-xxx-3 Series Proportional Electric
Spring Return Actuators on dampers with 1/2 to 3/4 in. or 12 to 19 mm round shafts, or 3/8 and 1/2 in.
or 10, 12, and 14 mm square shafts (quantity 1)
M9220-602 Replacement Locking Clips for M9210-xxx-3 Series Proportional Electric Spring Return Actuators
(five per bag)
M9220-603 Adjustable Stop Kit for M9210-xxx-3 Series Proportional Electric Spring Return Actuators (quantity 1)
M9220-604 Replacement Manual Override Cranks for M9210-xxx-3 Series Proportional Electric Spring Return
Actuators (five per bag)
M9220-610 Replacement shaft gripper, 10 mm square shaft with locking clip (quantity 1)
M9220-612 Replacement shaft gripper, 12 mm square shaft with locking clip (quantity 1)
M9220-614 Replacement shaft gripper, 14 mm square shaft with locking clip (quantity 1)
To Next Page
Loading...
