Serviceman Menu → Section 7.1.1
2 Installation Menu
-
9 Next
↓
1 Input BP Count → Section 7.2.5
2 TNI Blank
-
1 TNI Blank → Section 7.2.3
2 Make Sector → Section 7.2.3
3 Device Installation
-
1 Gyro → Section 7.1.6
2 Compass → Section 7.1.6
3 GPS Compass → Section 7.1.6
4 LOG → Section 7.1.6
5 2AXW → Section 7.1.6
6 2AXG → Section 7.1.6
7 GPS → Section 7.1.6
4 Network - 1 Network Function → Section 7.2.10
2
IP Address
3
Sensor Priority - 1 Primary → Section 7.2.10
2 Secondary → Section 7.2.10
4
Synchronization - 1 Day/Night → Section 7.2.10
2 Keyboard → Section 7.2.10
5 LAN Port Setting - 1
TX Setting - 1 TTM(TT) → Section 7.2.11
2 TLL(TT) → Section 7.2.11
3 TTD(TT) → Section 7.2.11
4 TLB(TT) → Section 7.2.11
5 OSD → Section 7.2.11
6 RSD → Section 7.2.11
7 ALR → Section 7.2.11
8 ACK → Section 7.2.11
9 Next
↓
1 TTM(AIS) → Section 7.2.11
2 TLL(AIS) → Section 7.2.11
3 TTD(AIS) → Section 7.2.11
4 TLB(AIS) → Section 7.2.11
2
RX Port - 1 Heading → Section 7.2.11
2 Speed → Section 7.2.11
3 AIS → Section 7.2.11
4 GPS → Section 7.2.11
5 DLOG → Section 7.2.11
6 Alarm → Section 7.2.11
7 Depth → Section 7.2.11
8 Temperature → Section 7.2.11
9 Next
↓
1 Wind → Section 7.2.11
2 Current → Section 7.2.11
3 ROT → Section 7.2.11
4 RSA → Section 7.2.11
5 Time Zone → Section 7.2.11
6 Date/Time → Section 7.2.11
3 RX Sentence
-
1 GPS(LL/COG/SOG)
→ Section 7.2.11
2 GPS(WPT/TIME)
→ Section 7.2.11
3 Depth
→ Section 7.2.11
4 Wind
→ Section 7.2.11
5 Current
-
1 Data Set Number
→ Section 7.2.11
2 Layer A
→ Section 7.2.11
3 Layer B
→ Section 7.2.11
4 Layer C
→ Section 7.2.11
6 Autopilot
→ Section 7.2.11
7
Line Monitor
3 Maintenance Menu
-
1 Safety Switch → Section 7.4.1
2 Area Initial
-
1 Partial Master Reset
-
1 Serviceman Menu → Section 7.4.2
2 Except Serviceman Menu → Section 7.4.2
3 User Setting → Section 7.4.2
4 TT Setting → Section 7.4.2
5 AIS Setting → Section 7.4.2
6 Day/Night → Section 7.4.2
7 JRC Card Copy Record → Section 7.4.2
2 All Master Reset → Section 7.4.2
3 Internal To Card 1/2 → Section 7.4.3
4 Card 1/2 To Internal → Section 7.4.3
5 TXRX Time
-
1 Clear TX Time → Section 7.4.4
2 Clear Motor Time → Section 7.4.4
3 TXRX to Display Unit → Section 7.4.4
4 Display Unit to TXRX → Section 7.4.4
6 String Data Update → Section 7.4.5
9 RADAR/TT Initial Setup
-
1 Signal Processing
-
1 Echo Noise Level → Section 7.3.1
2 Setting Mode → Section 7.3.1
2TT
-
1 Vector Constant → Section 7.3.2
2 Video TD Level → Section 7.3.2
3 Video High Level → Section 7.3.2
4 Video Low Level
5 Gate Size → Section 7.3.2
6 Limit Ring → Section 7.3.2
3 MBS
-
1 MBS Level → Section 7.3.3
2 MBS Area → Section 7.3.3