JRC RADAR 1800 - SECTION 4 Maintenance; General; Cleaning; Screw inspection

To Next Page

To Previous Page

114

Section 3 Operation

EDIT WAYPOINT EDIT IN CHART

ROUTE PLAN 00

STICK CURSOR CENTER

MOB MOB NO

NAV NAV

SELECT ROUTE WAYPOINT DIRECT

000

PLANNED ROUTE

SEQUENCE FWD

STEP AUTO

STOP WATCH 00:00:00.00

EBL/VRM EBL

MODE RADAR

CENTER CENTER

BRT/CLR BRIGHT 10

CONTRAST 5

Main Page

Before You Begin2
Symbols Used in this Manual3
Usage Hints4
EMC Installation & Service Guidelines6
Outside View8
- Table of Contents9
Definition on Terms17
SECTION 1 Introduction20
Function20
Features21
Components22
- Standard Equipment22
- GPS Sensor (Option)22
Construction23
System Configuration25
SECTION 2 Installation26
Installing the Display Unit26
- Choosing a Location for Installation26
- Standard Mounting26
- Console Mounting/ Surface Mounting28
Installing the Scanner Unit29
- Connecting the Scanner Unit Cable29
Installing the GPS/DGPS Sensor30
- Selecting the Position for Installation30
- Installation Procedure32
Connecting DC Power34
Grounding the Display Unit35
Connecting GPS/DGPS Sensor or Making NMEA0183 Data Connections (Option)36
Connecting Electronic Compass/Gps Compass (Option)38
Initial Operation and Set-Up38
- Inspection after Installation38
- Operating the INSTALLATION Menu39
- Radar Set up39
Connecting Personal Computer41
Inserting a Chart Card42
Removing a Chart Card42
SECTION 3 Operation43
Screen Layout43
Control Panel46
Rear Panel48
Basic Operations49
- The Power Control (Turning the Radar on and OFF)50
- LCD Backlight and Contrast Control50
- Display Modes50
- Vessel's Information/Waypoint's Information54
- Graph Display55
- Finding Function55
- Using the Jog Dial56
- Using the Joy Stick56
- Changing CURSOR Operation in RADAR/CHART Mode56
- General MEMU Operation56
- Buzzer ON/OFF57
- Setting LANGUAGE57
Radar Operation58
- Selecting a RANGE58
- Adjusting Receiver Sensitivity59
- Adjusting TUNING59
- Reducing SEA CLUTTER59
- Adjusting RAIN CLUTTER60
- Setting OFFSET60
- Range Measurement60
- Bearing Measurement61
- Changing CURSOR Operation Mode in RADAR/CHART Screen61
- RADAR Operating Menu62
- Rings62
- Display Mode (Bearing)62
- Interference Rejection63
- Setting AUTO/MANUAL SEA Clutter Rejection64
- Setting AUTO/MANUAL TUNING64
- Target EXPANDER64
- Process65
- Trails65
- Clear Trails66
- Waypoint66
- Setting Radar COLOR66
- Planned-Tx Mode67
- Setting GUARD ZONE68
- Display of RADAR Transponder70
Plotter Operation72
- Using the Joy Stick in CHART Mode72
- Man Overboard74
- Range Setting74
- Navigation Setting75
- Edit81
Menu Operations89
- General89
- Top Menu89
  - Radar Setting89
- Color90
- Tx-Plan91
- Plot Setting91
- Graph Setting94
- Gps Setting95
- Dgps Setting96
- Waas Setting97
- Installation98
Self Test Operation110
Master Reset and Language Select Operation111
SECTION 4 Maintenance116
General116
Scanner Unit116
- Radome Scanner Unit117
Display Unit117
- Cleaning the Display Unit Screen117
SECTION 5 Principle118
Radar Basics118
- Strength of Reflection from the Targets118
- Sea Clutters118
- False Echoes119
GPS/DGPS Basics121
- Gps121
- Differential GPS (DGPS)122
- Wide Area Augmentation System (WAAS)123
SECTION 6 Interswitch (Option)124
Outline124
- Components124
- Construction125
Installation126
- Setting Jumpers126
- Unit Connecting Cable127
Operation129
- The Following Is for the Jumpers in the Junction Box. (Setting 1)129
- The Following Is for the Jumpers in the Junction Box. (Setting 2)129
SECTION 7 After-Sales Service131
When Asking for Service131
Checks and Inspection131
SECTION 8 Disposal132
Disposal of LCD Module132
Handling Used Lithium Batteries132
SECTION 9 Specification133
General133
Scanner134
Display Unit135
Radar136
Plotter138
Input/Output Signal139
Appendices140
Wiring Diagram140
Geodetic System Table141
NMEA0183 Standard Input/Output Sentences142
- Input Sentences142
- Output Sentences143
Waypoint List144

JRC RADAR 1800 - SECTION 4 Maintenance; General; Cleaning; Screw inspection

Table of Contents

Related product manuals