Jura IMPRESSA X9 - Programming; Adjusting to Water Hardness; Setting the Time

11
E
14. Programming
The following parameters can be programmed:
쐌 Water hardness
쐌 Setup (product)
쐌 Time
쐌 Switch-on time
쐌 Switch-off time
쐌 Language
쐌 Display (unit and time format)
쐌 Information (number of products made, number of cleaning cycles
run)
14.1 Adjusting the machine to the water hardness
For this, please refer to Chapter 8 ‘Adjusting your machine to
the water hardness’.
14.2 Customizing (product definition)
You can program each product according to your preference.
Example: cappuccino
COFFEE READY
䡲 Press P (Fig. 5/E) until you hear an acoustic signal.
HARDNESS
䡲 Press the ‘+’ or ‘–’ key until SETTING appears on the display.
SETTING
䡲 Press P again (Fig. 5/E) to activate the SETTING programming step.
SETTING
PLEASE
SELECT
䡲 Select a product key of your choice. In our example it is cappuccino
(Fig. 1/E).
CAPPUCCINO
WATER
100 ML
䡲 Press P (Fig. 5/E) again to activate the setting programming step.
䡲 Press the ‘+’ or ‘–’ key until the required amount of water appears
on the display.
䡲 Press P (Fig. 5/E) to confirm your setting.
CONFIRMED
CAPPUCCINO
FROTH
20 SEC
䡲 Press P (Fig. 5/E) again to activate the programming step.
䡲 Press the ‘+’ or ‘–’ key to define the amount of frothed milk.
䡲 Press P to confirm your setting (Fig. 5/E).
CAPPUCCINO
MILK
20 SEC
䡲 Press P (Fig. 5/E) again to activate the programming step.
䡲 Press the ‘+’ or ‘–’ key to define the amount of frothed milk.
䡲 Press P to confirm your setting (Fig. 5/E).
䡲 Press the ‘+’ or ‘–’ key until POWDER appears on the display.
CAPPUCCINO
䡲 Press P (Fig. 5/E) again to activate the programming step.
䡲 Press the ‘+’ or ‘–’ key to set the coffee strength.
䡲 Press P to confirm your setting (Fig. 5/E).
CAPPUCCINO
GRINDER
50% 50%
䡲 Press P (Fig. 5/E) again to activate the programming step.
䡲 Press the ‘+’ or ‘–’ key to define the left and the right grinder.
䡲 Press P to confirm your setting (Fig. 5/E).
CAPPUCCINO
TEMP.
NORMAL
䡲 Press P (Fig. 5/E) again to activate the programming step.
䡲 Press the ‘+’ or ‘–’ key to set the temperature.
䡲 Press P to confirm your setting (Fig. 5/E).
䡲 Press EXIT (Fig. 5/K).
SETTING
PLEASE
SELECT
䡲 Press EXIT (Fig. 5/K) to leave this programming step or select the
next product key.
14.3 Setting the time
COFFEE READY
䡲 Press P (Fig. 5/E) until you hear an acoustic signal.
HARDNESS
䡲 Press the ‘+’ or ‘–’ key until TIME appears on the display.
TIME
12:00
䡲 Press P again (Fig. 5/E) to activate the TIME programming step.
TIME
HOURS
12:00
䡲 Press the ‘+’ or ‘–’ key to set the hours.
TIME
HOURS
14:00
䡲 Press P to confirm your setting (Fig. 5/E).
TIME
MINUTES
14:00
䡲 Press the ‘+’ or ‘–’ key to set the minutes.
TIME
MINUTES
14:45