To Next Page

• DonotconnecttheTVtothemainssupplyuntilyouhavecompletedalltheconnections.

• AlwaysdisconnecttheTVfromthemainssocketwhennotinuseforalongperiodoftime.

• The

buttonontheremotecontrolisonlyusedforswitchingtheTVintostandby,itdoesnotdisconnecttheTVfromthemainspower.

Tocompletelydisconnectthemainspower,pleaseremovethemainsplugfromthemainssocket.

PleaseinspectyourTVfordamageafterunpacking.Ifyoudonoticeanydamagepleaseconsultyourdealer.

Removeallpackagingfromtheunit.Retainthepackaging.Ifyoudisposeofitpleasedosoaccordingtoanylocalregulations.

 TV

 TVStand

 Screwsx4

 RemoteControl/

AAABatteriesx2

 YPbPrCable

 FAVCable

 InstructionManual

 QuickStartGuide

Unpacking

1. ConnectoneendoftheRFcoaxialcabletotheaerialsocketonthewall

andtheotherendofthecabletotheANTsocketonthebackofyourTV.

2. PlugtheTVintoamainssocketandswitchonatthemains.

3. Instandbymode,pressthe

buttonontheremotecontroltoturnthe

TVon.TheLEDindicatorwillashforafewsecondsthentheTVwill

switchon.

Connecting the Aerial and Turning on the TV

1. Slideopenthebatterycompartmentonthebackoftheremotecontrol.

Operating Your Remote Control

Thank youforpurchasingyournewJVCTV.

YournewTVincorporatesthelatesttechnologytoenhanceyour

viewingexperience.Wewouldsuggestthatyouallowabout20mins

forinitialsetup.

Pleasefollowthisguideforasuccessfulrsttimeinstallation.

Thelatesteco-friendlypower-savingtechnologywillswitcho

theTVifitisleftonandidlefor4hours.Pleasereferto“Auto

Standby”underthe“TimeSettings”sectionoftheinstruction

manualformoredetail.

Quick Start Guide

32" LED

Smart HD TV

LT-32C650

SCART

SPDIF

Coax.OUT

VGA

ANT.

HDMI 1(ARC)

HDMI 2

LAN

SCART

SPDIF

Coax.OUT

VGA

ANT.

HDMI 1

(ARC)

HDMI 2

LAN

RF coaxial cable

(not included)

2. InserttwoAAAsizebatteries.Makesuretomatchthe(+)and(-)

endsofthebatterieswiththe(+)and(-)endsindicatedinthebattery

compartment.

3. Slidethebatterycompartmentcoverbackintoplace.Makesureitclicks

intoplace.

Optional

Ifyouwanttoconnecttotheinternetviaawiredconnection

thenconnectyourethernetcabletotheLANsocket.

Need More Help!

IfyouneedhelpsettingupyourTVthenpleasecall:

UK: 0344 561 1234

Ireland: 1890 818 575

Linesareopen24/7

TheLCDdisplayisveryfragile,andmustbeprotectedatalltimeswheninstallingandremovingthebasestand.Besurethatnohardorsharpobject,

oranythingthatcouldscratchordamagetheLCDdisplay,comesintocontactwithit.DONOTexertpressureonthefrontoftheTVatanytimebecause

thescreencouldcrack.

Fitting the Stand to the TV

3. EnsuretheTVisswitchedoandnotconnectedtothemainspowersupply.

4. LaytheTVdownonaatsurfaceideallyontheedgeofatablesothebaseofthe

TVslightlyoverhangstheedgeofthetable,withthebacksidefacingup.Please

makesureasoftcushionedmaterial(suchasadrybathtowelorthickpieceof

foam)isplacedbeneaththescreen.

5. Slidethestandunderthelip,theneckwilltsnuglyoverthescrewholes.Then

screwthestandtotheTVusingthe4screwssupplied.

Fitting the Stand Neck and Base Together

1. Fittheneckontothebase.

2. Using4ofthesuppliedscrews,screwthenecktothebase.