FCC Compliance
Information
This device complies
with
Part
15
of
the
FCC
Rules. Operation is subject
to
the
following
two
conditions: (1)
this
device may
not
cause
harmful interference, and (2) this device
must
accept
any
interference received, including interference
that
may cause
undesired operation.
Changes
or
modifications
not
expressly approved
by
the
party
responsible
for
compliance could void
the
user's
authority
to
operate
the
equipment.
This equipment has been tested and
found
to
comply
with
the
limits
for
a Class B digital device, pursuant
to
Part
15
of
the
FCC
Rules. These
limits are designed
to
provide reasonable protection against harmful interference
in
a residential installation. This
equipment
generates, uses
and can radiate radio frequency energy and,
if
not
installed and used
in
accordance
with
the instructions, may cause harmful interference
to
radio communications. However, there is
no
guarantee
that
interference
will
not
occur
in
a particular installation.
If
this
equipment does cause harmful interference
to
radio
or
television reception,
which
can
be
determined
by
turning
the
equipment
off
and
on,
the
user is encouraged
to
try
to
correct
the
interference
by
one
or
more
of
the
following measures:
• Reorient
or
relocate
the
receiving antenna.
• Increase
the
separation between
the
equipment and receiver.
- Connect
the
equipment
into
an
outlet
on
a
circuit
different
from
that
to
which
the
receiver is connected.
- Consult
the
dealer
or
an experienced
radio/TV
technician
for
help.
FCC
SAR
Statement
This equipment complies
with
FCC
radiation exposure limits
set
forth
for
an
uncontrolled environment. End user
must
follow
the specific
operating instructions
for
satisfying
RF
exposure compliance. This transmitter
must
not
be
co-located
or
operating
in
conju
nction
with
any
other
antenna
or
transmitter.
The portable device is designed
to
meet
the
requirements
for
exposure
to
radio waves established
by
the
Federal Communications
Commission (USA). These requirements set a
SAR
limit
of
1.6
W/kg
averaged over
one
gram
of
tissue.
The
highest
SAR
value reported
under
this
standard during product certification.
Industry
Canada (IC) Compliance Statement
This device contains licence-exempt transmitter(s)/receiver(s)
that
comply
with
Innovation, Science and Economic Development Canada's
licence-exempt
RSS(s).
Operation is subject
to
the
following
two
conditions:
1. This device may
not
cause interference.
2. This device
must
accept
any
interference, including interference
that
may cause undesired operation
of
the device.
This equipment complies
with
ISED radiation exposure limits set
forth
for
an
uncontrolled environment. End user
must
follow
the specific
operating instructions
for
satisfying
RF
exposure compliance. This transmitter
must
not
be
co·located
or
operating
in
conjunction
with
any
other
antenna
or
transmitter.
The
portable device is designed
to
meet
the
requirements
for
exposure
to
radio waves established
by
the
ISED.
These requirements
set
a
SAR
limit
of
1.6 W/kg averaged
over
one
gram
of
tissue. The highest SAR value reported
under
this standard
during
product certification.
Avis
de
conformite
aux
normes
d'lndustrie
Canada
L'emetteur/recepteur exempt
de
licence contenu dans
le
present appareil
est
conforme aux CNR d'lnnovation, Sciences
et
Developpement
economique Canada applicables aux appareils radio exempts
de
licence. L'exploitation
est
autorisee aux deux conditions suivantes :
1.
L'appareil
ne
doit
pas produire
de
brouillage;
2. L'appareil
doit
accepter
tout
brouillage radioelectrique subi, meme si
le
brouillage
est
susceptible d'en compromettre
le
fonctionnement.
Cet
equipement
est
conforme aux limites d'exposition aux rayonnements d'ISDE etablies
pour
un
environnement non contr0le. L'utilisateur
final
doit
suivre les instructions d'utilisation specifiques
pour
se
conformer
a !'exposition
RF.
Cet
emetteur
ne
doit
pas
etre
colocalise ou
fonctionner
en
conjonction avec une autre antenne
ou
un
autre emetteur. L'appareil
portable
est
coni;u
pour
repondre aux exigences
d'exposition aux ondes radio etablies par ISDE. Ces exigences
fixent
une
limite
DAS
de
1,6 W /
kg
en
moyenne
sur
un
gramme
de
tissu. Valeur
DAS la plus elevee rapportee selon cette norme lors
de
la certification
du
produit.
i'IJjJ··••tttt••···jl
~~••m~z~~•~•ntt•~ff~~.~~-~~~~m•~~~m~•~••·m*~**•~~&ttz~tta~~·
~~-~~nuz~m~~~•mAA~~&T•~~-~;~gm~T•m•~·•~~~m•~~•~•T•~~~••~m•
M~~~•m•m~•m•~~m~~•z•••~m•
~~-~-fttt~~~~~-m~I•-~•a•~m•~•~tt••~~ZTS•
To Next Page
Loading...
