Kent Scientific SomnoSuite User Manual

SomnoSuite
®
Low Flow Anesthesia System
for Mice and Rats
User’s Guide

Kent Scientific SomnoSuite Specifications

General

Category	Laboratory Equipment
Control	Touchscreen Interface
Dimensions	Varies by configuration
Weight	Varies by configuration
Gas	Oxygen, Medical Air
Gas Delivery System	Closed-loop
Anesthesia Induction	Chamber or Mask
Temperature Control	Optional
Software	Optional
Power Requirements	100-240 VAC
Species	Mice, Rats, Small Animals
Vaporizer	Integrated precision vaporizer

Summary

Introduction and Navigation

System Components Overview

Details the physical parts of the SomnoSuite, including front and back panels.

Navigating the SomnoSuite Interface

Explains how to navigate module screens and access their parameters.

Touch Screen Menu Navigation

Details quick access to features and settings via the touch screen menu.

SomnoSuite Anesthesia Setup

Set Up Hardware

Covers connecting scavenging, and setting up air sources (internal pump or compressed gas).

Tubing Configurations

Guides on connecting accessory connectors to ports for chamber and nose cone setups.

Setup Examples

Illustrates connecting a 2-accessory connector for chamber and nose cone setup.

3-Accessory Connector Setups

Shows setup for chamber and two nose cones using a 3-accessory connector.

Advanced Setup Configurations

Illustrates connecting the SomnoSuite with an external ventilator.

SomnoSuite Operation and Procedures

Run Screen Overview and Initial Setup

Details the main run screen, anesthetic, and air flow settings.

Anesthesia Procedure Steps

Details steps for delivering anesthetic, including syringe installation and priming.

Syringe Empty Position Calibration

Explains how to recalibrate the syringe empty position for accurate measurements.

Anesthesia Delivery Steps

Details steps for induction, flushing the chamber, and directing airflow.

Anesthesia End Procedure

Covers reducing anesthetic concentration, stopping airflow, and animal recovery.

System Customization and Alarms

Custom Run Screen Configuration

Allows users to create a personalized display combining parameters from installed modules.

Parameter Location and Chart Settings

Lets users choose parameter display locations and customize graph settings.

Custom Run Screen Dial Menu

Explains how to assign dial commands for controlling settings on the custom run screen.

Alarms Configuration

Guides on setting custom alarms based on monitored parameters and triggers.

Alarm Management

Covers pre-set alarms and methods to silence or clear triggered alarms.

RoVent Ventilator Operations

Hardware and Air Source Setup

Covers connecting scavenging and setting up air sources for the RoVent ventilator.

Tubing Configurations for Use

Guides on connecting induction chamber and ventilator tubing to an endotracheal tube.

RoVent Connection Examples

Shows SomnoSuite connection with a 2-accessory connector for chamber and intubation.

RoVent Run Screen and Calibration

Explains the RoVent Run Screen interface, settings, and calibration procedures.

RoVent Procedure for Use

Guides on using RoVent in conjunction with SomnoSuite for anesthetic delivery.

RoVent Standalone Operation

Explains how to use RoVent independently for injectable anesthesia.

RoVent Configure Settings

Describes RoVent's operation based on specified inspiratory pressure or target tidal volume.

RoVent Advanced Settings

Covers PEEP, Sigh Breath, I/E Ratio, Inspiratory Pause, and Assist Mode configurations.

RoVent Special Modes and Triggers

Explains Pulse Mode and assigning RoVent functions to triggers.

RoVent Troubleshooting and Diagnostics

Tube and Exhaust Blockages

Addresses issues with open tubes, blocked tubes, and exhaust ports affecting pressure.

Regulation and Volume Deviations

Covers issues where peak pressure or tidal volume deviates from targets.

Tidal Volume and Deadspace Issues

Covers troubleshooting large rises/drops in tidal volume and deadspace calibration errors.

Diagnostic Procedures and Purge

Details access to diagnostic procedures and the purge function.

Performing a Leak Test

Guides on checking for internal and external leaks in the RoVent circuit.

MouseSTAT Pulse Oximeter Operations

Hardware Connection and Sensor

Guides on connecting the MouseSTAT sensor and interface cable to the SomnoSuite.

MouseSTAT Run Screen Overview

Explains the MouseSTAT Run Screen interface and its displayed parameters.

MouseSTAT Settings and Alignment

Details setting minimum heart rate and aligning the sensor for accurate readings.

MouseSTAT Troubleshooting and Maintenance

Sensor Light and Reading Issues

Addresses sensor connection, light status, and inconsistent or absent readings.

MouseSTAT Sensor Maintenance

Provides guidelines for maintaining the MouseSTAT sensor cable and cleaning.

CapnoScan CO2 Monitor Operations

CapnoScan Run Screen Overview

Details the CapnoScan Run Screen, including CO2 readings and waveform display.

Hardware Connection and Sampling

Guides on connecting the CapnoScan sensor, sampling assembly, and return line.

CapnoScan Calibration Procedure

Explains how to calibrate the CapnoScan sensor by zeroing it.

Gas Parameter Settings

Details setting CO2 units, measurement parameters, RR range, gas temperature, and pressure.

CapnoScan Troubleshooting and Maintenance

CO2 Reading and Connection Issues

Addresses issues with low or incorrect CO2 readings and connection problems.

CapnoScan Sensor Maintenance

Provides guidelines for maintaining and cleaning the CapnoScan sensor.

RightTemp Warming System Operations

Hardware Connection for Warming

Guides on connecting warming pad, body temperature sensor, and pad sensor.

Control Warming Methods

Details selecting warming methods: Off, Warming Pad, or Homeothermic.

Pad Temperature Regulation

Explains how to set and monitor the warming pad temperature.

Procedure for Homeothermic Use

Guides on placing the animal and inserting the temperature probe for homeothermic regulation.

RightTemp Troubleshooting and Maintenance

Heating and Sensor Issues

Addresses issues with pad heating, overheating, and sensor loss alarms.

RightTemp Pad and Sensor Maintenance

Provides guidelines for cleaning and maintaining the warming pad and sensors.

Data Management and PC Connectivity

PC Connections and Driver Setup

Explains how to connect devices to a PC and install necessary drivers.

Uploading Data to PC

Details the process of uploading data from the SomnoSuite to a PC via USB.

History - Internal Storage

Explains how the system stores parameters in ASCII format for later retrieval.

Viewing and Exporting History

Guides on how to access and view previously saved historical data.

Analog Output Configuration

Explains how to configure analog output for external equipment via a remote cable.

General Information and Specifications

Contact Information and Disclaimer

Includes contact details and legal disclaimers regarding system use and warranties.

Product Warranty Details

Details the one-year warranty coverage and exclusions for the SomnoSuite.

Satisfaction Guarantee Policy

Explains the process for technical support and product returns.

Controller and Power Supply Specs

Lists specifications for the SomnoSuite controller and its power supply.

SomnoSuite Recommended Flow Rates

Low-Profile Nose Cone Flow Rates

Recommended flow rates for the Low-Profile Nose Cone based on body weight.

Standard Face Mask Flow Rates

Recommended flow rates for the Standard Face Mask based on body weight.

Stereotaxic Mask Flow Rates

Recommended flow rates for the Stereotaxic Mask based on body weight.