Index-10 Service Guide N5227-90001
Index
procedures
caution about
, 7-3
warnings about, 7-3
replaceable cables, flexible
See cables, flexible
replaceable cables, RF
See cables, RF
replaceable cables, ribbon
See cables, ribbon
replaceable cables, wire harnesses
See cables, wire harnesses
replaceable flexible cables
See cables, flexible
replaceable hardware
in external analyzer
illustrated
, 6-81
part numbers
, 6-80
in fan assemblies
part numbers
, 6-72
in internal analyzer
illustrated
, 6-79
part numbers
, 6-78
in rear panel assembly
illustrated
, 6-71
part numbers
, 6-70
in top assembly
illustrated
, 6-73, 6-75
part numbers
, 6-74
replaceable parts
in front panel assembly
illustrated, 6-12
See section in Chapter 6 titled
Replaceable Parts Listings
replaceable RF cables
See cables, RF
replaceable ribbon cables
See cables, ribbon
replaceable wire harnesses
See cables, wire harnesses
replacement procedures
See section in Chapter 7 titled Removal
and Replacement Procedures
replacement sequence
, 4-3
return loss check
failure of, 3-13
test port cables, 3-13
rotary pulse generator (RPG)
illustrated, 6-10
part number
, 6-9
test, 4-15
troubleshooting
, 4-13
S
safety
considerations, 1-3
earth ground, 1-3
symbols
, 1-3
SCPI
, 8-9
screws
in external analyzer
illustrated
, 6-81
part numbers, 6-80
in rear panel assembly
illustrated
, 6-71
part numbers, 6-70
serial number
changing, 8-16
installing
, 8-16
service
battery
part numbers
, 6-82
contacting Keysight
, 2-6
options
, 2-6
procedures
caution about
, 7-3
post-repair
, 7-54
warnings about
, 7-3
static safety parts
part numbers
, 6-83
test equipment
required
, 2-5
tools
part numbers
, 6-82
warnings
, 1-4
warranty
standard
, 2-6
three-year return to Keysight
, 2-6
shipment for service or repair
, 2-6
signal processing ADC module (SPAM)
board
See A16
signal separation group
block diagram, 5-22, 5-23
defined
, 4-28
functional description of, 5-5
functional group
, 5-4
operation
, 5-20
troubleshooting
, 4-36, 4-37
single band failure
, 4-30
software
options, 8-14
solid state drive
See A55
source
adjustment, 3-42
calibration
, 3-42
functional group
, 5-4
group
block diagram
, 5-8, 5-9
defined
, 4-28
operation, 5-7
troubleshooting
, 4-30
match
cause of failure
, 8-11
definition of
, 8-11
measurements affected by
, 8-11
maximum output power test
, 3-30
power accuracy test
, 3-29
power linearity test, 3-31
step attenuator
removal and replacement
, 7-38, 7-39
troubleshooting, 4-39
source 1 board
See A5
source 1 synthesizer board
See A4
source 2 board
See A10
source 2 synthesizer board
See A17
SPAM board
See A16
speaker
troubleshooting, 4-13
specifications
instrument, 3-6
stabilization, warm up time
, 3-4
system
, 3-6
splitter
illustrated, 6-45, 6-51, 6-57, 6-63
part number
, 6-44, 6-50, 6-56, 6-62
removal and replacement
illustrated
, 7-29
procedure
, 7-28
troubleshooting, 4-32
stabilization
warm up time, 3-4
step attenuator
receiver
See A46 - A49
source
See A38 - A41
storage data
IDE, 5-35
strap handle
analyzer
illustrated
, 6-81
part number, 6-80
subgroup
data acquisition and processing, 5-31
front panel
, 5-31
subnet mask, LAN
, 4-19
substitution
cable, 3-23
calibration kits
, 3-23
verification kits
, 3-23
supplies
battery
part number
, 6-82
ESD
part numbers
, 6-83
support
contacting Keysight, 2-6
options
, 2-6
organization, 2-6
To Next Page
Loading...
