Keysight N5227A - Page 324

Index-12 Service Guide N5227-90001
Index
A14 frequency reference board, 4-31
A15 13.5 GHz LO synthesizer board
,
4-31
A16 SPAM board
, 4-42
A17 13.5 GHz source 2 synthesizer
bo
ard, 4-33
A20 power supply assembly
, 4-7
A21 CPU board
, 4-17
A24 IF multiplexer board, 4-42
A25 HMA26.5
, 4-32
A26 splitter
, 4-32
A27 mixer brick, 4-41
A28 mixer brick
, 4-41
A29 test port 1 receiver coupler
, 4-38
A3 display assembly
, 4-12, 4-13
A30 test port 3 coupler
, 4-38
A31 test port 4 coupler
, 4-38
A32 test port 2 coupler
, 4-38
A33 test port 1 coupler
, 4-38
A34 test port 3 coupler
, 4-38
A35 test port 4 coupler
, 4-38
A36 test port 2 coupler
, 4-38
A37 reference mixer switch
, 4-41
A38 test port 1 source step attenuator,
4-39
A39 test port 3 source step attenuator
,
4-39
A4 13.5 GHz source 1 synthesizer
bo
ard
, 4-33
A40 test port 4 source step attenuator,
4-39
A41 test port 2 source step attenuator
,
4-39
A42 test port 1 bias tee
, 4-39
A43 test port 3 bias tee
, 4-39
A44 test port 4 bias tee, 4-39
A45 test port 2 bias tee
, 4-39
A46 test port 1 receiver step
atten
uator
, 4-42
A47 test port 3 receiver step
atten
uator
, 4-42
A48 test port 4 receiver step
attenuator
, 4-42
A49 test port 2 receiver step
atten
uator, 4-42
A5 26.5 GHz source 1 board
, 4-33
A50 test port 1 mechanical switch
,
4-39
A52 test port 4 mechanical switch
,
4-39
A53 test port 2 mechanical switch,
4-39
A56, A57, A58, and A59 70 GHz doubler
bo
ards, 4-34
A7, A8, A12, and A13 40 GHz doubler
bo
ards
, 4-34
all traces, 4-29
check the basics
, 4-4
error term failure
suspect devices
, 8-3
fans
, 4-11
front panel
, 4-13
front panel keypad, 4-13
front panel knob
, 4-13
front-panel USB
, 4-13
GPIB CONTROLLER port, 4-17
inverter board
, 4-12
LAN
, 4-18
measurement system, 4-23
receiver group
, 4-40
running the receiver display
, 4-26
signal separation group
, 4-36
source group
, 4-30
traces A, B, C, D, R
, 4-26
where to begin
, 4-28
ping command
, 4-19
power output of receiver A
, 4-36
power output of receiver B
, 4-36
power output of receiver C
, 4-36
power output of receiver D
, 4-36
power up, 4-6
power supply check
, 4-7
rear panel
, 4-17
rear-panel USB, 4-17
receiver A
, 4-26, 4-36
receiver B
, 4-26, 4-36
receiver C, 4-26, 4-36
receiver D
, 4-26, 4-36
receiver outputs
, 4-41
receiver R, 4-26
RPG
, 4-13
signal separation group
, 4-37
source group
single vs. broadband
, 4-30
speaker
, 4-13
trace A
, 4-26
trace B
, 4-26
trace C
, 4-26
trace D, 4-26
trace R
, 4-26
typical power output
Port 1
, 4-37
Port 2
, 4-37
Port 3
, 4-37
Port 4, 4-37
using controllers to system
tr
oubleshoot
, 4-18
using error terms, 8-3
where to begin
, 4-4
U
uncertainty
measurement, 3-20
upgrade
analyzer, 2-4
firmware
, 8-17
downloading from the internet, 8-17
how to order
, 2-4
USB
accessories
part numbers, 6-83
board
See A2
port
rear panel connector
, 5-35
rear panel
troubleshooting
, 4-17
USB board
front panel
illustrated
, 6-12
USB controller board
front panel
illustrated
, 6-12
utility
option enable, 8-13
accessing
, 8-13
dialog box
, 8-13
V
VCO (voltage-controlled oscillator)
defined, 5-7
ventilation requirements , 1-3
verification
ANSI/NCSL Z540-1-1994, 3-8
kits
, 3-6
substitution
, 3-23
non-ANSI/NCSL Z540-1-1994, 3-9
of operating environment
, 3-4
of operating specifications
, 3-4
system
, 3-1, 3-6, 3-19
dialog box
, 3-23
example of results
, 3-26, 3-27
failure flowchart, 3-25
failure of
, 3-25
getting ready
, 3-4
interpreting results, 3-26
performing
, 3-22
procedure
, 3-23
what it verifies, 3-19
VGA
monitor, 4-12
port
rear panel connector
, 5-35
W
warm up
analyzer, 3-4
warning , 1-3
for servicing, 1-4