Smart Trunk Operation
When the Smart Key fob is in your possession and you are within close proximity to the back of the vehicle,
the hazard warning lights will blink, and a chime will sound for about three seconds to alert you that the
Smart Trunk is about to open.
The alert system will then blink and chime two additional times before opening the Smart Trunk.*
To enable the Smart Trunk, go to the Vehicle Settings in the infotainment system. Press SETUP > VEHICLE
> DOOR > SMART LIFTGATE.
Note
During the Smart Trunk alert, the Smart Trunk can be deactivated with the Smart Key by pressing any
button on the key fob.
Raising the Windshield Wiper Arms
To lift the wipers to clean the windshield, to inspect or replace the wiper blades, or to raise the wipers
in snow/ice conditions without damaging the hood, the blades need to be moved to the service position. To
move wiper blades to this position:
With the ignition ON, turn the ignition OFF, and within 20 seconds move the wiper switch to the MIST
position and hold the switch for more than two seconds until the wiper blade is in the fully upright position.
To return the wipers to the normal position, turn the ignition ON, then activate MIST.
Digital Key 2
*8
Digital Key 2, through your compatible smartphone, can be used to lock and unlock your vehicle and to start your vehicle without
needing to have a key fob.
Digital Key 2 Setup for Smartphones with Ultra-Wideband (UWB) Technology
1. Download the Kia Access App
5
and create an account.
2. Ensure your Smart Key is inside the vehicle and turn the vehicle on.
3. Activate Kia Connect
6
in your vehicle’s infotainment system.
4. Open the Kia Access App and select DIGITAL KEY
A
.
5. Press CREATE OWNER KEY.
6. When your vehicle’s infotainment system detects your device, the CONTINUE TO WALLET APP button will illuminate. Select it to
open the wallet app.
7. Press CONTINUE. The wallet app will pair up, and your digital key will be added.
Quick Tips
• When in the wallet app, click on the digital key and select the menu icon to adjust other settings or use other features.
• Actual steps may vary between devices.
Using Your Digital Key 2 (Smartphones with UWB)
1. To unlock or lock the doors, carry your smartphone, and touch the inside of the door handle to unlock.
Press the sensor on the outside of the door handle to lock.
2. Carry the smartphone inside the vehicle, press the brake pedal, and then press the start button to start
the vehicle.
For Digital Key 2 setup and operation for smartphones without Ultra-Wideband (UWB) technology,
see the Features & Functions Guide and Owner’s Manual.
Highway Driving Assist (HDA)*
9
HDA is designed to adjust the speed of the vehicle when driving on limited/controlled access
highways. The system can adjust the vehicle’s speed based on available highway speed information. The
automatic speed setting mode is designed to set the speed automatically by adjusting to the current
speed limits of the highway the vehicle is traveling on.
To enable/disable HDA, go to Vehicle Settings in the infotainment system. Go to Driver Assistance >
Driver Convenience > Highway Driving Assist.
To activate HDA, turn Smart Cruise Control (SCC) on by pressing the Driving Assist (Cruise) button
A
on the steering wheel controls.
When HDA is activated and the conditions are met, the Instrument Cluster indicator light
B
will
illuminate GREEN. If the conditions are not met, HDA will be in standby mode, and the indicator light
B
will illuminate WHITE.
When in operation, and if both lanes are recognized, a display
C
will show the lanes illuminated WHITE
and the steering wheel indicator illuminated GREEN.
If HDA is activated, conditions are met, and the SCC speed is set by the driver (at the posted highway
speed limit), HDA will enter the automatic speed setting mode. The set speed and AUTO will be displayed
in GREEN, and an audible alert will sound.
Reminders
• Current highway speed and controlled or limited access road information may vary. Future
navigation updates may change this information. See Owner’s Manual for more information.
• When the ignition is cycled, HDA returns to its previous state, on or off.
• If the driver changes the speed while in automatic speed setting mode, it deactivates and enters a
manual mode.
Surround View Monitor (SVM)*
10
SVM is a parking support system that shows the areas around the front, rear, left, and right sides of the
vehicle via four cameras displayed onto the infotainment system.
• Move the gearshift to R (Reverse) or press the Parking/View button
A
to turn on SVM. Press the button
again to turn OFF the function.
• Other view modes can be selected by touching the view icons
B
on the SVM screen.
• Surround View Monitor Auto On: With Driver Assistance > Parking Safety > Surround View Monitor
Auto On selected from the Settings menu, the front parking assist view screen is displayed when the
Parking Distance Warning alerts the driver while driving in D (Drive).
To change the SVM settings, press the on-screen settings icon
C
while SVM is operating.
Matte Paint* Care
To enjoy your vehicle’s matte appearance for many years to come, please follow these owner care and maintenance tips.
Dos and Don’ts
• Remove foreign substances such as insect remains, tar,
and road debris using a soft applicator and a mild solvent;
saturate and soak the area before cleaning
—
rub lightly.
• Hand-wash with a soft wash mitt and mild cleaning product
safe for matte paint.
• Use microfiber cleaning cloths with an alcohol-based
window cleaner for basic surface cleanup.
• Do not use wax, detail spray, or any products made for
normal paint. Use only products specifically developed
for matte finish paint.
• Do not use products that are even mildly abrasive, such as
polishes, glazes, or rubbing compounds.
• Do not use terry cloth, cloth, or paper towels. Do not rub the
finish vigorously; this will burnish the paint finish, causing a
permanent shiny spot. Shiny spots cannot be removed.
• Do not use commercial car wash facilities or their shine
enhancement products. Most car wash brushes, large
mechanized “towels,” and shine enhancement products
can damage matte paint.
• Do not use mechanical cleaners or polishers.
A
B
C
(
B
u
t
t
o
n
s l
o
c
a
t
e
d o
n
right side of
s
t
e
e
r
i
n
g
w
h
e
e
l
)
0 mph
0 KMH
0 20 40 60
１00
96
Lv１
66
PWR
60 MPH
0 mph
0 KMH
１00 kWh /１00m
96 %
Lv１
READY 66°F
PWR
60 MPH
A
B
C
To Next Page
Loading...
