Kia SELTOS - Advanced Driver Assistance Systems (Adas); Blind-Spot Collision-Avoidance Assist (BCA)

ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPERATING INFORMATION AND SAFETY WARNINGS. *IF EQUIPPED †LEGAL DISCLAIMERS ON BACK INSIDE COVER
11
RES
SET
CNCL
+
–
CRUISE
OK
RES
SET
CNCL
+
–
CRUISE
OK
RES
SET
CNCL
+
–
CRUISE
OK
RES
SET
+
–
CRUISE
OK
RES
SET
+
–
CRUISE
OK
RES
SET
+
–
CRUISE
MODE
OK
RES
SET
+
–
CRUISE
CANCEL
CANCEL
OK
RES
SET
+
–
CRUISE
CANCEL
OK
MODE
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
ADAS
Refer to the inside front cover for
more information on QR codes.
www.youtube.com/KiaFeatureVideos
QR CODES
Blind-Spot Collision-
Avoidance Assist
Video
Blind-Spot Collision-Avoidance Assist (BCA)
†6
REMINDERS:
• BCW will not issue a warning
if the vehicle speed is 6 mph
or more above the surrounding
vehicles
• When BCW is ON and the
ignition is cycled, BCW returns
to its previous state
• BCW is a supplemental system.
Do not solely rely on this
system. Always pay attention to
the road and drive safely
The BCA system is not a substitute
for safe and proper driving. Always
drive safely and use caution.
Refer to section 5 in the Owner’s
Manual for more information.
The images on this page are for
illustrative purposes only and
may not reflect actual feature or
operation.
•
• BCW Warning Volume can be adjusted in the User Settings in
the Instrument Cluster or the Vehicle Settings* on the audio head
unit. Go to Driver Assistance, then Warning Volume
• BCW will activate when:
– The system is turned on
– Other vehicles are detected on the rear sides of the vehicle
– Vehicle speed is above approximately 20 mph
QUICK TIP
A
B
BCW uses rear corner radar sensors in the rear bumper to monitor and warn the driver in certain situations if it detects an
approaching vehicle in the driver’s blind spot area and before changing lanes. When turned on, the system will activate when the
vehicle is traveling faster than 20 mph and will alert the driver if another vehicle is detected by the rear-corner radar sensor.
1st-stage warning: When another vehicle is detected within BCW warning boundary
A
,
an indicator will illuminate on the outside rearview mirrors
B
.
2nd-stage warning: When 1st stage warning is on and the driver activates a turn signal,
a flashing yellow indicator will illuminate on the outside rearview mirrors and the system
will sound a warning.
BCW User Settings:
• To turn BCA on, go to the User Settings menu in the Instrument Cluster, press the
Mode button
C
on the Steering Wheel when the vehicle is at a standstill, gear
shift in Park and with the ignition switch or the Engine Start/Stop button* in the ON
position, and select User Settings . Press the Move (OK) button
D
up/down and
select Driver Assistance, Blind-Spot Safety and then press the OK button
D
• Some models access settings through the Vehicle Settings in the audio head unit.
Press the Setup hard key on the audio head unit, then VEHICLE on the screen
to enter Vehicle Settings
• To set BCW when in Blind-Spot Safety, select:
– Warning Only: Vehicle will provide a warning only (audible & visual)
– Off: System is off, no warnings provided
• To set the initial warning activation time, go to User
Settings , then Driver Assistance, Warning Time and
press the OK button
D
. Adjust the warning timing:
– Early/Normal: Maximizes the amount of distance
between the vehicles before the initial warning occurs
– Late: Reduces the amount of distance between
the vehicles before the initial warning occurs
C
D
(Type A; Controls located on right side of Steering Wheel)