EasyManuals Logo

Kichler Lighting 15309BKT Quick Start Guide

Kichler Lighting 15309BKT
2 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
FOR USE WITH LANDSCAPE LIGHTING SYSTEMS ONLY.
1) The device is accepted as a component of a landscape lighting system
where the suitability of the CSA or UL labeled combination shall be deter
mined by CSA, UL respectively or the local inspection authorities having
jurisdiction.
2) Fixture shall be connected to an extra low voltage transformer approved
for use with landscape lighting systems.
3) Thisxtureistobeconnectedtoasecondarywiringofthefollowingtype:
12 GA 60°C minimum type;
SPT-3 suitable for outdoor use; or
approved landscape lighting cable.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE,OR INJURY TO
PERSONS
IMPORTANT SAFETY INSTRUCTIONS
Lighted lamp is HOT!
WARNING — To reduce the risk of FIRE OR INJURY TO PERSONS.
1) Turn off / unplug and allow to cool before replacing lamp.
2) Lamp gets HOT quickly! Contact only switch / plug when turning on.
3) Do not touch hot lens or cowl.
4) Do not remain in light if skin feels warm. (Light is intense, it may cause
“sunburn”.)
5) Do not look directly at lighted lamp.
6) Keep lamp away from materials that may burn.
7) Useonlywithwattageandlampmarkedonxture.
8) Do not touch the inner glass envelope of the lamp at any time. Use a soft
cloth. Oil from skin may damage lamp.
9) Donotoperatethexturewithadamagedormissinglens.
CAUTION
WHEN INSTALLING KICHLER LANDSCAPE LIGHTING (LINE VOLTAGE OR LOW VOLTAGE),
CARE SHOULD BE TAKEN TO KEEP CLEAR OF POTENTIALLY COMBUSTIBLE MATERIALS.
WHEN MAINTAINING THE FIXTURES, BE SURE TO REMOVE LEAVES, PINE NEEDLES,
GRASS CLIPPINGS, MULCH, OR ANY DEBRIS THAT HAS ACCUMULATED ON THE LIGHT
BULB, LENS, OR BODY OF THE FIXTURE.
ASSEMBLY AND INSTALLATION
1) Determinedesiredlocationformountingxture.
2) Pass wire from swivel through hole in top of stake.
3) Screw stake onto bottom of swivel.
4) At desired location push stake into ground. If ground is hard and stake is
difculttoinstall,makeacrosscutingroundusingaatshovel.
5) Turn cowl counter clock wise and remove cowl and rubber gasket.
Date Issued: 12/2/11 IS-15309-CB
OUTDOOR USE ONLY
DOM ETRE INSTALLE A L’EXTERIEUR
INSTRUCTIONS
For Assembling and Installing Fixtures in Canada
Pour L’assemblage et L’installation Au Canada
LAMP
LAMPE
SWIVEL
PARTIE PIVOTANTE
STAKE
PIQUET
FIXTURE BODY
LUMINAIRE
COWL
CYLINDRE
RUBBER GASKET
RONDELLE DE CAOUTCHOUC
For warranty information please visit: http://www.landscapelighting.com/portal/warranty_page
Pour de plus amples informations sur la garantie, cliquez sur le lien ci-dessous : http://www.landscapelighting.com/portal/warranty_page
QUIC DISC
WIRING INSTRUCTIONS
Turn off power.
Thefulllengthofthe18GAxturewiremaybeusedtoconnectwiththe10GAor12GAcableprovidedthefollowingconditionsaremet:
•Wiringistobeprotectedbyroutingclosetothextureoraccessoryorsecuredtoabuildingstructuresuchashouseordeck.
• 18GAxturewiringistobecutoffsothatitisattachedtotheconnectorwithin6inchesofthextureorbuildingstructure.
• Ifitisnecessarytomaketheconnectionsunderground,thennomorethan6inchesofthe18GAxturewireistobeburied.
The Quic Disc
connector is designed to install onextureandaccommodatesone18GAxturewireandone 10 GA or one 12 GA supply wire.
Place the 10 gauge supply wire across the area marked 10 GA on Quic Disc
or place the 12 gauge supply wire across the area marked 12 GA
on Quic Disc
.
Placethe18gaugexturewireacrosstheareamarked18GAontheQuicDisc
. After the wires are in place, connect the top of the Quic Disc
tothebasewithsuppliedscrew,makingsurethatthewiresremainatinthebottomportionoftheQuicDisc™,andthescrewistightenedall
the way down.
Thecoppercontactswillautomaticallypiercethewires’insulation.Excess18GAxturewirethatsticksouttheendoftheQuicDisc
is to be cut off.
Makenootherwiringconnectionstothe18GAxturewire.
6) Installlamptosocketinsidexturebody.NOTE: Use caution when
installing. Hold lamp by outer housing. DO NOT touch glass envelope
inside. If this happens, clean lamp with denatured alcohol and a lint-free
cloth.
7) Re-assemblecowlandrubbergaskettoxturebody.
8) Angleofxturecanbeadjustedbylooseningscrew.
9) Turn off power.
10) Make wire connections using supplied Quic Disc
following instructions
below, or using other approved wiring connection method (not supplied.)

Other manuals for Kichler Lighting 15309BKT

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Kichler Lighting 15309BKT and is the answer not in the manual?

Kichler Lighting 15309BKT Specifications

General IconGeneral
TypePath Light
StyleTraditional
MaterialMetal
Voltage12V
Bulb TypeLED
Number of Bulbs1
Color Temperature3000K
CRI80
FinishBlack
Depth6 inches
Location RatingWet

Related product manuals