Kirisun PT8000 - Trouble Shooting Guide; Major Specifications

PT8000 Service Manual
10
1. Press and hold P1 while turning the radio power ON to enter
the Wired Clone Mode. The display will show “C”. If wired clone
function is disabled, the radio will enter User Mode.
2. Connect the slave radio to the master radio by the cloning cable
(KCL02) and turn on the power of the slave radio.
3. Press and hold P2 on the master radio to start cloning. Then the
LED on the master will light red. The data of the master is sent to
the slave. While the slave is receiving the data, the display shows
“P” and the LED lights green. When cloning of data is completed,
the red LED on the master will go out, and the slave radio will
restart automatically.
4. You can continue to clone the data according to step 3.
Note: The user can enable or disable the wired clone function
through PC programming software. Once the wired clone function
is disabled, the radio cannot enter the Wired Clone Mode.
Chapter 6 Disassembly for Maintenance
The radio is a kind of sophisticated communication equipment
with precise structure and small size. You should disassemble it
carefully during the maintenance. The instructions for the
disassembly are as follows.
6.1 Exploded View
33
31
30
29
26
26
19
19
6
32
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
25
24
22
21
20
19
18
17
16
27
28
面壳组件装配
23
Figure 6.1
No. Part No. Description PCS
1 201-008000-R02 Volume Knob 1
2 203-006800-R26 Circlip for Knob 1
3 203-007200-R08 Nut for Knob 1
4 204-006800-R01 LCD Protective Film 1
5 LOGO 1
6 301-25050J-R01 Screw M2.5*5 6
7 201-008000-R01 Front Cabinet 1
8 204-008000-R01 Dustproof Net for Speaker 1
9 121-100000-R21 Speaker 1
10 120-400000-R14 Speaker Wire 1
11 120-400000-R15 Flat Cable 1
12 204-008000-R02 Upper Dustproof Strip for Front
Cabinet
1
13 204-008000-R03 Lower Dustproof Strip for Front
Cabinet
1
14 203-008000-R02 Al Top Case 1
15 120-100000-R15 Power Cable 1
16 201-008000-R06 Power Cable Fastener 1
17 203-008000-R03 Metal Baffle Plate 1
18 202-008200-R02 Rubber Plug for External Speaker
Jack
1
19 303-30100G-R01 Screw M3*10, with Spring Washer
20 203-008200-R03 Antenna Connector
21 102-304452-R01 Power Module 1
22 203-008200-R05 Shield for Power Module 1
23 204-008200-R10 Electric Conductive Cushion 1
24 Mainboard Assembly 1
25 301-30060G-R01 Screw M3*6 8
26 204-008000-R04 Dustproof Strip between Top and
Bottom Al Case
2
27 203-008000-R01 Al Bottom Case 1
28 301-30250D-R01 Screw M3*25 6
29 201-008000-R04 Light Guide 1
30 201-008000-R03 Lens 1
31 202-008000-R01 Rubber Key 1
32 PCB Assembly 1
33 302-26060D-R01 Screw M2.6*6 5
6.2 Instruction for Disassembly of the Radio for Maintenance
1) RF-PCB disassembly
① Screw off the six M3*25 screws on the Al bottom case, and
remove the Al bottom case (See Figure 6.2).
② Remove the shield for power module, and then remove the
solder of the power module on the PCB with a soldering iron (See
Figure 6.2).
③ Screw off the four M2.5*5 screws on the baffle plate, and then
remove the metal baffle plate, the power cable fastener and the
Front Cabinet Assembly