Need help?Do you have a question about the KitchenAid KFCP22EXMP and is the answer not in the manual?
This document describes a KitchenAid Bottom Mount Refrigerator, model KFCP22EX, providing essential information for its electrical connection, water supply, and installation requirements.
The KitchenAid Bottom Mount Refrigerator is designed to store food items, keeping them fresh and cool. It features a bottom-mounted freezer compartment, which typically offers more convenient access to fresh food items stored in the upper refrigerator section. The refrigerator is equipped with an ice maker and a water dispenser, providing convenient access to chilled water and ice. These features require a dedicated cold water supply to function properly.
To ensure safe and optimal operation, the refrigerator requires a specific electrical setup. It operates on a 115-volt, 60-Hz, AC-only electrical supply, and needs a 15- or 20-amp fused, grounded circuit. It is highly recommended to use a separate circuit exclusively for the refrigerator to prevent overloading and ensure consistent power. The electrical outlet should not be controlled by a switch, meaning it should provide continuous power. For safety, extension cords should never be used with this appliance.
The refrigerator's ice maker and water dispenser require a cold water supply with a pressure between 30 and 120 psi (207 and 827 kPa). If you have concerns about your home's water pressure, it is advisable to consult a licensed, qualified plumber. For households using a reverse osmosis (RO) water filtration system, the pressure of the water entering the refrigerator's water inlet valve from the RO system must also be within the 30 to 120 psi (207 to 827 kPa) range. If the RO system is connected directly to the cold water supply, the water pressure to the RO system itself needs to be a minimum of 40 to 60 psi (276 to 414 kPa) to ensure proper functioning.
Before performing any maintenance tasks, such as installation, cleaning, or replacing a light bulb, it is crucial to disconnect the refrigerator from its electrical source. This is done by turning the control (Thermostat, Refrigerator, or Freezer Control, depending on the specific model) to the "OFF" position and then unplugging the appliance. Once the maintenance is complete, the refrigerator should be reconnected to the electrical source, and the control should be reset to the desired setting. Detailed instructions for using the controls can be found in the "Using the Controls" section of the full manual.
Proper ventilation is essential for the refrigerator's efficient operation and longevity. During installation, it is necessary to allow for a 1/2 inch (1.25 cm) space on each side and at the top of the refrigerator. Additionally, at least 1 inch (2.54 cm) of space should be left between the back of the cabinet and the wall. If the refrigerator includes an ice maker, extra space at the back is needed to accommodate the water line connections.
When installing the refrigerator next to a fixed wall, a minimum clearance of 2 1/2 inches (6.3 cm) on the hinge side is required. This clearance allows the door to swing open fully without obstruction, which is important for accessing the interior and for removing drawers or shelves for cleaning. The exact clearance needed may vary slightly depending on the specific model.
To prevent potential damage and ensure optimal performance, it is recommended not to install the refrigerator near heat sources such as an oven or radiator. High ambient temperatures can force the refrigerator to work harder, consuming more energy and potentially reducing its lifespan. Furthermore, the refrigerator should not be placed in a location where the ambient temperature is likely to fall below 55°F (13°C), as this can also affect its performance and efficiency.
General| Brand | KitchenAid |
|---|---|
| Model | KFCP22EXMP |
| Category | Refrigerator |
| Type | French Door |
| Total Capacity | 22 cu. ft. |
| Ice Maker | Yes |
| Water Dispenser | Yes |
| Energy Star Certified | Yes |
| Counter Depth | Yes |
| Color | Stainless Steel |
| Height | 69.875 inches |
| Width | 35 3/4 in |
