Klëarvue Cabinetry 478-3923 - User Manual

Sliding Base x1
Socket Head Screw x6
SS-10.1297
Handle x2
SS-10.1292
Basket Rack x1
Washer x6
SS-10.1298
Handle Screw x2
SS-10.1293
Exterior Basket x2
SS-10.1295
Basket Clip x10
SS-10.1294
Drill Template x1
SS-10.1291
Interior Basket x2
SS-10.1296
Mounting Screw x6
SS-10.1299
Hex Wrench x1
THIS EDGE ON CABINET INTERIOR WALL
THIS SIDE UP
THIS EDGE ON CABINET INTERIOR WALL
FOR RIGHT HAND SWING DOOR
CABINET
OPENING
THIS EDGE ON CABINET INTERIOR WALL
FOR LEFT HAND SWING DOOR
CABINET
OPENING
SKU 478-3923
BLIND CORNER PULLOUT
SS-10.1291
DRILL TEMPLATE
FOR
17-
15
/16"
16-
9
/16"
Instructions for SKU 478-3923
BLIND CORNER PULLOUT
KIT INCLUDES:
QUESTIONS?
Contact Customer Care
1-800-721-4191
Monday – Friday 8-5 Central Time
ADJACENT
BASE CABINET
ADJACENT
BASE CABINET
28-
1
/4"
18-
3
/4"
FILLER
BLIND CORNER
BASE CABINET
ADJACENT
BASE CABINET
EXTERIOR
BASKET
INTERIOR
BASKET
EXTERIOR
BASKET
INTERIOR
BASKET
ADJACENT
BASE CABINET
28-
1
/4"
FILLER
BLIND CORNER
BASE CABINET
WALL
WALL
18-
3
/4"
ADJACENT
BASE CABINET
ADJACENT
BASE CABINET
28-
1
/4"
18-
3
/4"
FILLER
BLIND CORNER
BASE CABINET
ADJACENT
BASE CABINET
EXTERIOR
BASKET
INTERIOR
BASKET
EXTERIOR
BASKET
INTERIOR
BASKET
ADJACENT
BASE CABINET
28-
1
/4"
FILLER
BLIND CORNER
BASE CABINET
WALL
WALL
18-
3
/4"
LEFT HAND SWING DOOR
RIGHT HAND SWING DOOR
IMPORTANT: Please read before you begin the blind corner pullout installation.
!
SIX PILOT HOLES
PILOT HOLES
Open Slots
STEP 1:
● Place the drill template (SS-10.1291) on the bottom of the cabinet so that the black arrows
are facing towards the opening and against the side of the cabinet as shown below.
● Using a
1
/16" drill bit, drill a pilot hole at all six mounting locations on the template. Make sure
to not drill completely through the bottom of the cabinet.
● Remove the template from the cabinet.
To nd all Klëarvūe Cabinetry® installation instructions and installation videos, visit www.klearvuecabinetry.com
NOTE:
● Blind Corner Pullout (478-3923) is intended for use with the Klëarvūe Blind Corner Base
Cabinet (478-0079).
● Check the diagrams below for dimensions of the unit when opened. Make sure no island
cabinets or appliances will intrude in this space.
● Before installing the pullout, install the blind corner cabinet hinges (478-9838 included with
the cabinet box) to the cabinet. Do not install the door front until the blind corner pullout is
completely installed.
STEP 2:
● Remove four socket head screws (SS-10.1217) and washers (SS-10.1298) from the top plate on
the sliding base as shown below.
STEP 3:
● Place the sliding base on the bottom of the cabinet. Make sure the four open slots in the top
plate are on the same side as the cabinet opening.
● Attach the sliding base to the cabinet using the six mounting screws (SS-10.1299).

Klëarvue Cabinetry 478-3923 Specifications