Need help?Do you have a question about the KLIM Ai-1 Airbag Vest and is the answer not in the manual?
General| Brand | KLIM |
|---|---|
| Model | Ai-1 Airbag Vest |
| Category | Safety Equipment |
| Language | English |
Details of the manufacturer, Teton Outfitters DBA Klim USA.
Identifies the product as a Motorcyclist airbag, Ai-1 Airbag Vest.
Specifies the inflation system as Electronic autonomous In&motion airbag.
Ensures correct positioning of protection areas on thorax, abdomen, and back.
Table to select the appropriate airbag vest size based on body measurements.
Prohibits any modification to the airbag system or its components.
PPE offers impact protection, not total protection against all injuries.
Acknowledges inherent dangers of motorcycling and user responsibility for safety.
No protective garment offers complete protection; use with other PPE is advised.
Protective equipment should not encourage increased risk-taking.
Improper handling of the vest can seriously reduce protection.
The vest must be used with its protectors inserted for functionality.
Advises refraining from motorsports if dangers are not understood.
Specifies the operational temperature range for the airbag system.
Detailed steps for cleaning the airbag vest and its components.
Vest offers optimal protection only when the airbag system is inflated.
Guidelines for storing and transporting the vest and In&box.
Instructions for visually inspecting the vest for damage before use.
Product must be serviced/repaired by KLIM; no modification allowed.
Advises following local regulations for recycling the product.
Information on vest lifespan, warranty, and inflation limits.
Refers to jacket compatibility section for usage.
Refers to inflator replacement section for details.
Lists and describes the vest and airbag system components.
Description of the In&box as the detection and triggering device.
Details about the inflator, including handling and expiration.
Cautionary advice on handling the high-pressure gas generator and its expiration.
Guidance on discarding or recycling expired inflators.
Procedure to check if the inflator is full and properly connected.
Explains the meaning of LED indicators for inflator status.
Details on the certified back protector and its specific usage.
Instructions and warnings for replacing the inflator.
Warning about touching the inflator connector during replacement.
Steps to follow after the airbag system has been deployed.
How to check the vest's integrity after an inflation event.
Detailed steps for safely removing the used inflator.
Crucial safety advice for handling the inflator during removal.
Requirement for a clean and dry environment for inflator replacement.
Steps to open the vest and unclip the inflator from its housing.
Warning against forcing the connector or pulling the cable.
Verifying the seal's condition after inflator removal.
Steps to check the system's integrity after removing the inflator.
Using the inflation adapter for system checks and testing.
Procedure to inflate the vest and check for leaks using a pump.
Steps to install the replacement inflator into the vest.
Ensure the airbag system is deflated before installing the new inflator.
Instructions on how to correctly screw in the new inflator.
Steps to reconnect the inflator connector securely.
Securing the inflator in its designated place within the vest.
Using the In&box to confirm the new inflator connection.
Guide for charging the In&box, specifying charger requirements.
Steps to power on the In&box unit.
Requirement to activate the In&box online before use.
Introduction to LED indicator meanings on the In&box.
Information on the In&box battery duration.
Advice on conserving battery by switching off when not in use.
Explains LED indicators related to inflator status on the In&box.
Meaning of no light on the In&box, indicating it is off.
Explains LED indicators related to inflator and GPS functionality.
Explains the meaning of battery level indicator LEDs.
Details the meaning of different battery LED colors and states.
Step-by-step guide for correctly inserting the In&box into the vest.
Crucial alignment step for correct In&box insertion using arrow indicators.
How to secure the In&box using the locking mechanism.
Important visual cue to confirm correct locking by checking markings.
Instructions on how to properly wear and fit the airbag vest.
Vest must be worn under a jacket for abrasion resistance.
Prohibits wearing the vest without an outer protective layer.
Information on compatible jackets and restrictions.
Lists restrictions like backpacks, harnesses, and neckbrace use.
Specific KLIM suit model tested for compatibility.
Using non-compatible suits can cause malfunction and injury.
General recommendations for using the airbag vest.
Vest textile is not abrasion resistant; requires jacket coverage.
How to check jacket compatibility through measurements.
How to measure the user's body for jacket compatibility.
How to measure the jacket for compatibility.
Defines the criteria for jacket compatibility based on measurements.
Strong warning against using the vest with incompatible jackets.
Details about the notified body and CE certification.
Information on locating the production year or serial number.
Reference to section (N) for expiration date information.
Specifies the standard the vest is certified against.
Explains CE marking and EU regulatory conformity.
Links to online declarations of conformity.
Analysis of injury concentration in motorcycle accidents.
Clarifies areas the vest does not protect (limbs, head).
Factors affecting the airbag system's detection capabilities.
Emphasizes user's responsibility for their own safety.
System cannot compensate for dangerous or illegal behavior.
Essential checks required before each use of the airbag system.
Warns against use by individuals with specific medical conditions.
Advises against use for individuals with back or neck issues.
Prohibition for users with breast prostheses.
Prohibition for pregnant women.
Requirement to remove piercings in the vest's covered area.
Warning against carrying sharp objects that could damage the cushion.
Vest provides impact protection, not abrasion resistance.
Guidance on resolving issues with the vest or In&box.
Specifies the intended applications for the back protector.
Exclusively for motorcycle use; other applications are prohibited.
Protects against impacts with the ground or obstacles during accidents.
No system offers total protection against all injuries.
Guidance on selecting the correct back protector size.
How to correctly fit and wear the back protector for optimal protection.
Specifies the minimum dimensions of the back protector's protection area.
Details the protection levels based on residual force.
Explains the meaning of the CE marking and conformity.
Specifies the operational and storage temperature limits.
Requirements for a clean, dry storage area for the back protector.
How impact can affect the back protector and pre-use checks.
Strict prohibition on modifying the back protector or its components.
Recommended cleaning method for the back protector.
Do not clean the inflator or its connector with water.
Prohibits bleach, ironing, machine washing, dry cleaning, hair dryers, and detergents.
Instructions for product disposal and recycling in accordance with local laws.
Details of the certifying notified body and their address.
Information on the registered trademark and company address.
To Next Page