Klipsch 500 - Page 4

lirE Speaker Placement in Listening Area
IilD Placement of Center Channel
Below
~Above
I
81
TV
( )
I
81 4-
I--
0
I~
6'·15'
~I
0
Sub
=-rv----l
Sub
----
0
I
c
I
0
X=V=l
X
~~
Optional
,Sl: rear placementSR
'····'B B'·
IirmJ Speaker Wire / Subwoofer Hook Up
Klipsch Subwoofer Amp Panel
'HUE
'.0' <G' O·
o. <f!> Off "
AUTO
C)LWlL
, ..... Mo'.'OO MAll
"'_. I.OWPASS
,9) \ '''''
80 110
WARNING
TOAVOID THE RISK OF FIRE OR
ELECTRIC SHOCK. DO NOT EKPOSE
THIS eQUIPMENT TO RAIN OR MOISTURE
ATTENTION
CAUTION
FOR CONTINUED PROTECTION
AGAINST RIStl:, Of FIRE, REPLACE ONLY
WITH SAME TYPE fUSE AND RATING.
UTIUSER UN FUSIBLE DE RECHANGE
DE MEME TYPE ET CALIBRE_
..
J. ~120V-5OI.0'"
--t 100watts
Sub
Su,rcUI'lll $1111'011""
left Right
Center
Front
Right
Front
left
AV Receiver
Terminal
Posts on
Speakers
NOTE: The AN receiver/surround sound processor must be set to "Subwoofer On"
and all speakers set to "small".
The suggested crossover point is 150 Hz. If 150 Hz is not available, use 120 Hz.
REMARQUE : Le processeur ambiophonique / recepteur audiovisuel doit etre regie
sur « Subwoofer On » et to utes les enceintes sur « Small». La frequence de coupure
suggeree du filtre est 150 Hz. Si 150 Hz n'est pas disponible, utiliser 120 Hz.
HINWEIS: Der AN-Receiver/Surroundsound-Prozessor muss auf "Subwoofer On"
und aile Lautsprecher auf "Small" (klein) eingestellt werden. Die empfohlene
Crossoverfrequenz betragt 150 Hz. Wenn 150 Hz nicht verfugbar ist, wahlen Sie 120 Hz.
NOTA: e necessario impostare iI processore del suono surround/ricevitore audio-video
su "Subwoofer On" e tutti i diffusori su :'Small".11 punto di crossover suggerito e di
150 Hz; se questa frequenza non e disponibile, usare 120 Hz.
For additional hook up options, please refer to your
AV Receiver manual or klipsch.com
NOTA: 0 receiver de AN/processador de som surround deve ser configurado para
"Subwoofer On" (Subwoofer Iigado) e todas as caixas aCIJsticas devem ser configuradas
para "small" (reproduCao atenuada de graves). 0 ponto de crossover sugerido e 150 Hz.
Se 150 Hz nao estiver disponivel, use 120 Hz.
NOTA: EI procesador de sonido surround 0 receptor de AN se debe configurar en
"subwoofer encendido" (Subwoofer On) y todos los altavoces se deben configurar
en "pequeno" (Small). La frecuencia de crossover que se sugiere es 150 Hz. Si no se
dispone de 150 Hz, fije la frecuencia en 120 Hz.
i1::l!: {f!Wi/t5IJ~tt~~)':~~f'~~~~J'I~&;,~~g5t:5Ett '1t£{f~JD)\ttlffl~~*~
(Subwoofer On) J ' :illzHPJT1'fB"Jm~~~5t:5Ett I IJ\ (small) J 0
pJT~~B"J::x:]ZJUi~150 Hz 0 Bi~1'f 150 Hz ' ~lJf~m 120 Hz 0
~
3502 Woodview Trace
Indianapolis, IN 46268
1-800-KLIPSCH • klipsch.com
© 2009 Klipsch Group, Inc,