How to fix a Kogan Air Conditioner that won't turn on?
If your Kogan Air Conditioner doesn't start, here are a few things to check: * There might be power outages, so wait until power is restored. * The power plug may be loose, so ensure it is tightly inserted into the outlet. * The power switch fuse may have blown, so replace the fuse. * The timer might be set, so wait for the timer to complete, or cancel the timer settings.
Why is my Kogan KASHSAC26UA blowing air but not cooling well?
If your Kogan Air Conditioner isn't cooling or heating effectively, check for these possible causes: * Dust accumulation on the filter, which requires cleaning the filter and removing any obstacles at the air inlet and outlet, as well as adjusting the louver blades. * Open doors or windows, or an unclosed exhaust fan, which requires closing them. * The auxiliary heating function may not be activated (for models with this feature), so turn it on. * Incorrect mode settings, so re-select the mode and adjust the temperature and wind speed accordingly.
What to do if Kogan KASHSAC26UA won't turn on right after being turned off?
If the air conditioner is turned on immediately after it is turned off, the protective delay switch will delay the operation for 3 to 5 minutes.
Why does my Kogan KASHSAC26UA stop after starting?
If your Kogan Air Conditioner stops running after starting, it could be due to a few reasons: * It may have reached the set temperature, which is a normal function. * It may be in a defrosting state, and it will automatically resume running after defrosting. * The shutdown timer may be set, so turn it on again if you want to continue using it.
What to do if my Kogan KASHSAC26UA has water droplets?
If there are water drops on your Kogan Air Conditioner's indoor unit, it could be due to: * High ambient humidity, which is a normal phenomenon. * Prolonged cooling in an open space, which requires closing the doors and windows. * Too small an opening angle of the louver blades, so increase the angle.
Why does my Kogan KASHSAC26UA make noise?
If your Kogan Air Conditioner's indoor unit is making abnormal sounds, it could be due to: * The sound of the fan or compressor relay switching on or off, which is normal. * Too much dust accumulation on the air filter, so clean the air filters. * Too much air noise when 'Strong fan' is turned on, so deactivate the 'Strong wind' function if it's uncomfortable.
How to get rid of bad smell from Kogan KASHSAC26UA?
If the indoor unit of your Kogan Air Conditioner blows out an odor, clean the air filter or activate the cleaning function. The air conditioner itself does not have an undesirable odor.
Why does my Kogan Air Conditioner blow mist?
This is because the indoor air is cooled rapidly when the indoor temperature and humidity are high. This is normal.
General| Model | KASHSAC26UA |
|---|---|
| Cooling Capacity | 2.6kW |
| Heating Capacity | 2.6kW |
| Refrigerant | R410A |
| Power Supply | 220-240V, 50Hz |
| Type | Split System Air Conditioner |
| Air Flow (Indoor Unit) | 380m³/h |
| Operating Temperature Range (Cooling) | 18°C to 43°C |
| Operating Temperature Range (Heating) | -7°C to 24°C |
Lists the components included in the indoor unit package.
Lists the components included in the outdoor unit package.
Details the parts and features of the indoor air conditioner unit.
Details the parts and features of the outdoor air conditioner unit.
Illustrates and labels the buttons and functions of the remote control.
Provides crucial initial guidelines and requirements for the installation process.
Details the steps for inspecting the air conditioner unit after unpacking.
Outlines essential safety precautions that must be followed during installation.
Specifies ideal locations and environmental conditions for installing the unit.
Checks to be performed on the installation environment before proceeding.
Details the specifications and standards for the unit's mounting structure.
Specifies electrical safety standards and wiring requirements for installation.
Details electrical wiring specifications and cable gauge requirements for North America.
Details electrical wiring specifications for regions other than North America.
Safety measures for installation and operation at elevated heights.
Specifies the correct procedures and precautions for grounding the unit.
Provides spacing requirements and visual guide for indoor unit installation.
Diagram and details of the mounting bracket used for installation.
Instructions and methods for creating wall-through holes for piping.
Illustrates and explains how to route the connecting pipes and cables.
Step-by-step guide for connecting the pipes between indoor and outdoor units.
Instructions for insulating and securing the piping and cables.
Steps for securely mounting the indoor unit onto the installed bracket.
Detailed steps for connecting the interconnection cord to the indoor unit.
Checks to perform after the installation is complete.
Diagrams and spacing requirements for installing the outdoor unit.
Details the steps and diagrams for connecting the unit's wiring.
Procedure for creating a vacuum in the refrigerant system using R32 refrigerant.
Explains the drainage system for condensation and defrosting water.
Checks to ensure electrical safety after installation.
Verifies the security and correctness of the installation.
Methods for detecting refrigerant leaks after installation.
Procedures for preparing and performing operational tests after installation.
Instructions for downloading and connecting the AC Freedom mobile application.
Specifies the operational temperature limits for cooling and heating modes.
Provides specific information and considerations for the heating operation mode.
Information on how the air conditioner manages shutdown sequences.
Instructions for operating the unit using the force switch when the remote is unavailable.
Guide on adjusting the direction of airflow using the remote or manually.
Instructions for cleaning the front panel of the indoor unit.
Steps for removing and cleaning the air filter of the indoor unit.
Instructions for reinstalling the cleaned air filter and closing the unit panel.
Pre-operation checks to ensure the unit is ready for use.
Post-operation tasks for maintaining the unit and remote controller.
Details the necessary qualifications and training for maintenance staff.
Pre-maintenance checks of the installation site and safety equipment.
General work area, safety checks, and precautions for maintenance operations.
Procedures for checking R32 refrigerant leaks during maintenance.
Steps for removing refrigerant and vacuuming the system.
Requirements and procedures for charging refrigerants into the system.
Procedures and considerations for safely scrapping and recovering refrigerants.
Troubleshooting steps for when the air conditioner fails to operate.
Troubleshooting steps for immediate start-up issues after shutdown.
Troubleshooting steps for when the unit stops running intermittently.
Troubleshooting steps for poor cooling or heating performance.
Troubleshooting steps for when the indoor unit emits unpleasant odours.
Explanation and troubleshooting for sounds of running water during operation.
Explanation for slight clicking sounds during unit start-up or shutdown.
Troubleshooting for various abnormal sounds from the indoor unit.
Explanation and troubleshooting for water drops appearing on the indoor unit surface.
Explanation for mist being blown from the indoor unit outlet during cooling.
To Next Page
