www.Komatsu.com Printed in Japan 200801 IP.AD (10)
CEN00075-02
Materials and specifications are subject to change without notice.
is a trademark of Komatsu Ltd. Japan.
HORSEPOWER
Gross: 671 kW
899 HP @ 2000 rpm
Net: 664 kW 890 HP @ 2000 rpm
OPERATING WEIGHT
108390 kg
238,960 lb
D475A-5E0
Photo may include optional equipment.
● Air conditioner with heater and defroster
● Air-suspension seat
● Alternator, 100 A/24 V
● Auto-priming system
● Back-up alarm
● Batteries, 200 Ah/4 x 12 V
● Blower fan
● Decelerator pedal
● Dry-type air cleaner with dust evacuator
and dust indicator
● Eight-roller track frames
● Final drive case wear guard
● Hinged underguard with front pull hook
● Hydraulic track adjusters
● Lighting system (including four front
and two rear lights)
● Lockup torque converter
● Mirror
● Mirror, rearview
● Muffler with rain cap
● Perforated front mask
● Radiator reserve tank
● ROPS brackets
● Seat belt
● Segmented sprockets
● Shoes, 710 mm 28" extreme service,
single-grouser
● Starting motors, 2 x 7.5 kW/24 V
● Steel cab
● Steering control
● Sun visor
● TORQFLOW transmission
● Tr ack roller guards
● VHMS (without orbcomm)
● Warning horn
● Water separator
● Wet steering clutches
STANDARD EQUIPMENT
● Additional cab heater
● Battery isolator
● Coal dozer
● Counterweight
● Double wiper
● Dual tilt dozer
● Fast fuel fill
● Fire extinguisher
ROPS*:
Weight . . . . . . . . . . . . . . . . 940 kg 2,070 lb
Dimension:
Width . . . . . . . . . . . . . . . . . . 1940 mm 6'4"
*Meets ISO 3471, SAE J1040 APR88, ROPS
standards.
Multi-shank ripper:
Hydraulically controlled parallelogram ripper
with three shanks. Ripping angle variable
and depth adjustable in two stages.
Weight (including hydraulic
control unit) . . . . . . . . 9720 kg 21,430 lb
Beam length . . . . . . . . . . . . 3085 mm 10'1"
Maximum lift above ground . 1196 mm 3'11"
Maximum digging depth . . . . 1124 mm 3'8"
Steel cab**:
Weight . . . . . . . . . . . . . . . . 455 kg 1,000 lb
Dimension:
Length. . . . . . . . . . . . . . . 1790 mm 5'10"
Width . . . . . . . . . . . . . . . . 1455 mm 4'9"
Height from compartment
floor to ceiling . . . . . . . . 1530 mm 5'0"
**Meets ISO 3449 FOPS standard.
Variable giant ripper:
Variable, parallelogram single-shank ripper
ideal for ripping up tough material. Ripping
angle is variable. Ripping depth is adjustable
in four stages by a hydraulically controlled
pin puller.
Weight (including hydraulic
control unit) . . . . . . . . 7360 kg 16,230 lb
Beam length . . . . . . . . . . . . 1477 mm 4'10"
Maximum lift above ground . 1196 mm 3'11"
Maximum digging depth . . . . 1744 mm 5'9"
● Hydraulics for ripper
● Lattice front mask
● Light for ripper
● Orbcomm
● Prelubrication
● Push plate
● Radio-AM/FM cassette
● Safety glass
● Shoes:
—
810 mm 32"
—910 mm 36"
● Spill guards
● Strengthened Semi-U blade
● Strengthened U blade
● Tr ack shoe slip control system
OPTIONAL EQUIPMENT
C
RAWLER
D
OZER
To Next Page
Need help?
General
