120
Program operating mode
Page 16 - Amp EG
Amp envelope
Start/Attack/Break/Sustain/Release Level
These parameters are the level of the envelope segment.
0…99 Level value.
Start Level
This parameter specifies the volume level at note-on. If
you want the note to begin at a loud level, set this to a
high value.
Attack Level
This parameter specifies the volume level that will be
reached after the attack time has elapsed.
Break Level
This parameter specifies the volume level that will be
reached after the decay time has elapsed.
Sustain Level
This parameter specifies the volume level that will be
maintained from after the slope time has elapsed until
note-off occurs.
Attack/Decay/Slope/Release Time
These parameters specify the time over which the vol-
ume change will occur.
0…99 Time value.
Attack Time
This parameter specifies the time over which the volume
will change after note-on until it reaches the attack level.
If the start level is 0, this will be the rise time of the sound.
Decay Time
This parameter specifies the time over which the vol-
ume will change from when it reaches the attack level
until it reaches the break point level.
Slope Time
This parameter specifies the time over which the vol-
ume will change from when it reaches the break point
level until it reaches the sustain level.
Release Time
This parameter specifies the time over which the vol-
ume will change after note-off until it reaches 0.
Amp EG ‘Level’ modulation
AMS(L) (Alternate Modulation Source)
This parameter specifies the source that will control the
“Level” parameters of the amp EG. See “AMS (Alter-
nate Modulation Source) list” on page 124.
Intensity
This parameter specifies the depth and direction of the
effect that “AMS” will have. For example, if “AMS” is
Velocity, setting “Start Level Swing”, “Attack Level
Swing” and “Break Point Level Swing” to + and setting
“Intensity” to a positive (+) value will cause the amp
EG volume levels to increase as you play more
strongly. Setting “Intensity” to a negative (–) values
will cause the amp EG volume levels to decrease as you
play more strongly. With a setting of 0, the levels will
be as specified on “Page 16 - Amp EG”.
-99…+99 Intensity value.
Start Level Swing
This parameter specifies the direction in which “AMS”
will change “Start Level”. If “Intensity” is set to a posi-
tive (+) value, setting this parameter to + will allow
AMS to increase the EG level, and setting this parame-
ter to – will allow AMS to decrease the EG level. With a
setting of 0, no change will occur.
Attack Level Swing
This parameter specifies the direction in which “AMS”
will change “Attack Level”. If “Intensity” is set to a pos-
itive (+) value, setting this parameter to + will allow
AMS to increase the EG level, and setting this parame-
ter to – will allow AMS to decrease the EG level. With a
setting of 0, no change will occur.
Break Point Level Swing
This parameter specifies the direction in which “AMS”
will change “Break Level”. If “Intensity” is set to a pos-
itive (+) value, setting this parameter to + will allow
AMS to increase the EG level, and setting this parame-
ter to – will allow AMS to decrease the EG level. With a
setting of 0, no change will occur.
Note-on
Note-off
Attack
Time
Decay
Time
Release Time
Attack Level
Sustain
Level
Time
Break Point
Start
Level
Slope
Time
Amplifier EG
Volume
Amp 1 EG changes (Level) (AMS=Velocity, Intensity = a positive (+) value)
Note-on
Note-off
Note-on
Note-off
Note-on
Note-off
Softly played note when Start
Level Swing=0 and Attack Level
Swing and Breack Level Swing
are set to +
Strongly played note when
Start Level Swing=0 and Attack
Level Swing and Breack Level
Swing are set to +
Strongly played note when
Start Level Swing=0 and Attack
Level Swing and Breack Level
Swing are set to +
To Next Page
Loading...
