Kreg PRS2100 - Precision Benchtop Router Table Safety; Router Operation Safety Guidelines; Extension Cord Guidelines; Recommended Router Bit Speeds

9
Safety Instructions Specic To Operating The Precision Benchtop Router Table
a) Read, understand, and follow your router manufacturer’s safety warnings
and instructions.
b) Disconnecttherouterfrompowerbeforemakingadjustments.Never
adjust the fence, plate, reducing rings, or any part of the router or router table
while the router is running.
c) Placetheroutertableonaatsurfacetopreventtippingorsliding.
Neverstandontheroutertable.
d) Donotattempttoroutwarped,twisted,orbowedworkpieces.All
workpiecesmusthaveatfacesandsquareedges.
e) Donotattempttoroutverylargeworkpiecesonaroutertable.
Verylargeworkpiecescanbedifculttocontrolandcancausetheroutertableto
tip over.
f) Onlyuserouterbitsinyourrouter.Neverusetoolssuchascarvingburrs,
mounted abrasives, wire wheels, or drill pits, even if the shanks match the
diameter of the router collet.
g) Weargloveswhenhandlingrouterbits. Cutting edges are sharp.
h) Neverusedirty,dull,ordamagedrouterbits. Remove wood-resin build-up
withacleanerspecicallyformulatedforcuttingtools.Havedullbitssharpenedby
aqualiedperson.Discarddamagedbits.
i) Makesureatleast75%oftherouter-bitshanklengthissecurelyheldinthe
router collet. To ensure a secure hold, leave
1
⁄16 to
1
⁄8 (2mm-3mm) between
the end of the bit shanks and the bottom of the collet.
j) Usetheinsert-platereducingringwiththesmallestopeningthatallowsthe
bittopassthroughit. A large gap around the bit can allow the workpiece to tip
into the bit and kick back.
k) Positionthefencefacesascloseaspossibletothebit. Turn the bit by hand
to check for interference. Firmly tighten the fence-face T-knobs before routing.
l) Adjustrouterspeedtomatchthediameterofthebit. Reduce router speed
when using large-diameter bits. See the Table at right for recommended router
speeds.
m) Makesuretheroutermotorissecurelyclampedinthebasebefore
starting the router.
n) Always support the workpiece with the fence or start pin. Only use the
starter pin with router bits that have a guide bearing.
o) Whenusingthefence,alwayspositionthebitguardovertherouterbit
andasclosetotheworkpiecesurfaceaspossible.
p) Neverremovealargequantityofstockinonecut.Make several
progressively deeper cuts, adjusting the router bit or fence position between cuts.
q)Keephandsawayfromtherotatingbitandyourbodyoutofthepathof
the cut. Always use the bit guard, Use push sticks, push blocks, and feather
boards whenever possible, especially when routing narrow workpieces. Turn off
the router before clearing parts of scrap.
r) Avoid awkward hand positions, where a sudden slip could cause contact
withtherotatingbit.Neveroverreach.
s) Avoid routing small parts.Routtheproleonalargeworkpieceandthencut
theparttonalsizefromthelargeworkpiece.Ifyoumustroutasmallpart,build
an appropriate jig or hold the part with a wood handscrew clamp.
t) Makesuretheworkpieceisclearofthebitandthebitcomestoacomplete
stopbeforeadjustingtheworkpieceposition.Neverstarttherouterwiththe
workpiece in contact with the bit.
u) Avoidkickbacks.Kickbacksoccurwhentheworkpiecebindsorliftsoff
thetablewhilebeingrouted,causingittobethrownbacktowardthe
operator. To avoid kickbacks and potential injury, use sharp bits, keep the
machine aligned and maintained properly, and adequately support the workpiece.
Do not attempt to rout workpieces that are twisted, warped, or bowed, or that have
loose knots.
v) Feedtheworkpieceagainst(notwith)thebitrotation. The bit can grab a
workpiece fed with the rotation of the bit, violently eject it from the router table, and
can cause your hand to contact the bit.
w) Nevertrapaworkpiecebetweenthebitandthefence. When forming a
proleonthestraightedgeofaworkpiece,alwaysroutwiththebithousedinthe
fence and the edge of the workpiece against the fence.
x) Wheneverroutingaproleinwhichmaterialisnotbeingremovedbelowa
protrudingportionofthebit,orapartoftheproleistrappedbetween
cuttersaboveandbelow,takeextraprecautionstopreventtheworkpiece
fromliftingoffthetablesurfaceduringrouting.A workpiece lifting off the table
cankickbackandcauseseriouspersonalinjury.Whenroutingtheseproles,itis
especiallyimportanttousestraight,atstockandavoidwarped,bowed,ortwisted
stock.
y) Periodically check the tightness of fasteners and adjustment and locking
knobsandthealignmentofthefence.Loose fasteners and knobs and a
misaligned fence can cause personal injury.
z) Thisroutertableisdesignedforaspecicapplication.Donotmodifyand
or use it for any other application. If you have questions relative to the
applicationoftheroutertable,DONOTuseituntilyouhavecontactedKregTool
Company and have been advised accordingly.
Guidelines for extension cord use
Extension cords are only to be used for temporary purposes. They do not replace
the need for installation of outlets and proper wiring where necessary.
In the shop and on construction sites:
1. Extension cords with an equipment grounding conductor must be used at all
times.
2. Extension cords must be protected from damage, and not run through doorways
or windows where the doors or windows can close, causing damage to the cord.
3. Extension cords must be a minimum of 16 AWG and be rated for the equipment
in use.
4. Extension cords must be periodically inspected to ensure that the insulation and
conductivity of the wires are not compromised.
5. Extension cords should not be run through water or allowed to have connections
that may be exposed to accumulated water.
Always follow bit manufacturer’s speed recommendations. Some bit designs require
specicspeedsforsafetyorperformance.
!
WARNING When using electric tools, always follow the safety precautions belowtoreducetheriskofre,electricshock,andpersonalinjury.
Read all these instructions before attempting to operate this product. SAVETHESEINSTRUCTIONS.
Recommended Router Bit Speeds
Bit Diameter Maximum Speed (RPM)
 24,000


18,000


16,000


12,000
WARNING:
!
This product can expose you to chemicals including Acrylonitrile
and other chemicals, which are known to the State of California to cause cancer and
reproductive harm. For more information go to www.P65Warnings.ca.gov.
WARNING:
!
Drilling, sawing, sanding or machining wood products can
expose you to wood dust, a substance known to the State of California to cause
cancer. Avoid inhaling wood dust or use a dust mask or other safeguards for
personal protection. For more information go to www.P65Warnings.ca.gov/wood.