Krone Big Pack 890 XC - Page 191

Terminal – Menus [Medium/Comfort Version Electronics]
191
Pos: 103.100 /Üb erschriften/Übersc hriften 3/K-O /M/Menü 1-1 „ Korrekturwert Ballenlänge“ @ 381\mod_ 1444116959866_7 8.docx @ 275 1834 @ 3 @ 1
16.6.1 Menu 1-1 "Correction value for bale length"
Pos: 103.101 /BA/I nfo-Center/CC I-ISOBUS-Ter minal/CCI-BiG Pack/Haupt menüs/Hauptme nü 1 Einstellu ngen/Menü 1-1 „ Korrekturwert B allenlänge“ Einf ührung @ 381 \mod_1444117 027238_78.doc x @ 2751865 @ @ 1
Because of the different properties of materials (e.g. straw, silage) the actual bale length may
deviate from the set setpoint value. The correction value can be used to correct this deviation.
Pos: 103.102 /BA/I nfo-Center/CC I-ISOBUS-Ter minal/CCI-BiG Pack/Haupt menüs/Hauptme nü 1 Einstellu ngen/Menü 1-1 „ Korrekturwert B allenlänge“ Bild @ 381\mod_ 14441170726 48_78.docx @ 2 751896 @ @ 1
CC000097
CC000029_2
1-1-1
Fig.
111
Pos: 103.103 /BA/I nfo-Center/CC I-ISOBUS-Ter minal/CCI-BiG Pack/Haupt menüs/Hauptme nü 1 Einstellu ngen/Menü 1-1 „ Korrekturwert B allenlänge“ M enü aufrufen @ 381\mod_14441 19074203_78. docx @ 275 1927 @ @ 1
Menu 1 "Knotter" has been selected, see chapter Terminal – Menus, "Menu 1 'Knotter'".
• To open the menu, press .
The display shows the "Correction value for bale length" menu.
Pos: 103.104 /BA/I nfo-Center/CC I-ISOBUS-Ter minal/CCI-BiG Pack/Haupt menüs/Hauptme nü 1 Einstellu ngen/Menü 1-1 „ Korrekturwert B allenlänge“ Tab elle Grafiken @ 354\mod_1 43825717804 3_78.docx @ 2645 673 @ @ 1
Display area
Item
Designation
Explanation
1
Correction value for bale length
• Adjustable value range: 90 – 110 %
• If a correction value of e.g. 110 %
is set, the bale will be 10 % longer.
• Factory setting: 100 %
Pos: 103.105 /BA/I nfo-Center/CC I-ISOBUS-Ter minal/Menüs b edienen/Wert ändern_Ver weis @ 367\mod _1441282809 440_78.docx @ 2 694885 @ @ 1
Changing the value
• Increase or reduce the value, see chapter Terminal – Menus, "Changing the value".
Pos: 103.106 /BA/I nfo-Center/CC I-ISOBUS-Ter minal/Menüs b edienen/Wi ederkehrende Sym bole_Verweis @ 354\mod _1438323278518_ 78.docx @ 26 48185 @ @ 1
Recurring symbols
• See chapter Terminal – Menus, "Recurring symbols".
Pos: 103.107 /La yout Module /---------------Seitenumbruch---------------- @ 0\mod_119 6175311226_0. docx @ 4165 @ @ 1