Maintenance - hydraulic system
356
Pos: 138.1 /Übersc hriften/Überschrif ten 2/P-T/P Presskraftreg elung (bei Not-H and-Betätigu ng) @ 24\mod _1241612862 815_78.docx @ 2 46772 @ 2 @ 1
21.6 Pressing force control (with emergency manual activation)
Pos: 138.2 /BA/ Wartung/Großpac kenpressen/H ydraulikanlage / Bordhydrauli k/Warnung - Pr esskraftregelu ng im Notbetrie b @ 274\mod _1404218701 576_78.docx @ 2061073 @ @ 1
Warning!
There is an increased risk of injury if adjust the force of pressure in emergency mode.
The force of pressure can be adjusted in emergency mode while the machine is running. As a
result, people may be caught by machine components and seriously injured or killed.
• Ensure that the machine can be turned off immediately if there is danger.
• Special caution must be exercised when making the adjustment.
Pos: 138.3 /BA/ Wartung/Großpac kenpressen/H ydraulikanlage / Bordhydrauli k/Einstellen Pressdruck / Pr esskanal lösen Bild @ 24\mod _1241612327331 _78.docx @ 246699 @ @ 1
Fig.
Setting the baling pressure
Releasing the bale channel
chamber
Pos: 138.4 /BA/ Wartung/Großpac kenpressen/H ydraulikanlage / Bordhydrauli k/Presskraft einst ellen im Notbe trieb Einführtext @ 274\mod _1404220039 645_78.doc x @ 2061421 @ @ 1
If the electronics fail, you can continue to work with the machine for a short time in emergency
mode. The force of pressure is adjusted while the machine is running.
Pos: 138.5 /BA/ Wartung/Großpac kenpressen/H ydraulikanlage / Bordhydrauli k/Achtung! - S chäden an der M aschine, d urch überschreite n der Presskr aft. @ 274\mod _1404220579 001_78.docx @ 20 61484 @ @ 1
ATTENTION!
Exceeding the force of pressure may damage the machine.
Without electronic control, the maximum force of pressure can be exceeded. This can lead to
significant damage to the machine.
• Never work for a long time without the electronic control system.
Pos: 138.6 /BA/ Wartung/Großpac kenpressen/H ydraulikanlage / Bordhydrauli k/Einstellen des Pr essdruckes @ 24\mod_12 41612910315 _78.docx @ 246797 @ 3 @ 1
21.6.1 Setting the baling pressure
The baling pressure on the bale channel chamber flaps can be adjusted on the hydraulic control
block (1) on the left side of the machine under the side hood.
To perform a setting:
• Set the desired pressure by slowly screwing in the knurled head screw (2) (the pressure is
limited to a maximum of about 100 bar / 1450 PSI)
• Read the pressure on the pressure gauge (4)
Pos: 138.7 /BA/ Wartung/Großpac kenpressen/H ydraulikanlage / Bordhydrauli k/Hinweis Ränd elschraube ganz herausdrehen @ 24\mod_ 124161316606 5_78.docx @ 2 46845 @ @ 1
Note
After emergency manual activation has been performed, the knurled head screw (2) must be
completely screwed out again.
Pos: 138.8 /BA/ Wartung/Großpac kenpressen/H ydraulikanlage / Bordhydrauli k/Presskanal l ösen (Komfort) @ 24\mod_124 1613287237_7 8.docx @ 24 6869 @ 3 @ 1
21.6.2 Releasing the bale channel chamber (comfort)
The "Release bale channel flaps" seat valve is located on the right next to the hydraulic control
block (1) for pressing force control on the left side of the machine under the side hood.
To perform a setting:
• The bale channel chamber flaps loosen by slowly screwing in the knurled head screw (2) as
far as it will go
Pos: 139 /Layou t Module /---------------Seitenumbruch---------------- @ 0\mod_11961 75311226_0.doc x @ 4165 @ @ 1
To Next Page
Loading...
