Operation
167
Pos: 48.99.44 / BA/Bedienung /R undballenpresse/N etz- un d Folienbindung_A usführung N etz- und Folien bindung ab 17 18 /Hinweis zu Folie nbindung_A ugen in der Ab bildung_Ver weis auf Bindemateri albremse @ 5 13\mod_150 3481005959_7 8.docx @ 3530 075 @ @ 1
Note
The lug symbols in the picture indicate important points where you need to proceed differently
when inserting a film than when inserting a net.
– In case of chamber film wrapping, the clamping lever (12) must not touch the film roll (1).
To this end, the clamping lever must be set, see chapter Settings, "Locking/releasing the
clamping lever".
Pos: 48.99.45 /Ü berschriften/Ü berschriften 3/A- E/A/Anzahl d er Netz- oder F olienlagen einst ellen @ 513\ mod_15034084 90607_78.doc x @ 3529676 @ 3 @ 1
11.19.5 Setting the number of net or film layers
Pos: 48.99.46 / BA/Bedienung /R undballenpresse/N etz- un d Folienbindung_A usführung N etz- und Folien bindung ab 17 18 /Anzahl der N etz- oder Folie nlagen einstelle n siehe Kapitel T erminal @ 51 3\mod_1503408 661118_78.do cx @ 3529708 @ @ 1
The number of net or film layers is set at the terminal, see chapter Terminal – Menus, "Menu 1,
number of net layers" or "Menu 1, number of film layers".
Pos: 48.99.47 /Ü berschriften/Ü berschriften 3/F- J/H/Hinweise zum Betrieb mit Folienbindu ng @ 507\mod_ 150046785560 3_78.docx @ 3 487367 @ 3 @ 1
11.19.6 Notes on operation with chamber film wrapping
Pos: 48.99.48 / Beipacks/Rundball enpressen/Folie nbindung/M odulgruppen Foli e einlegen / L ED Lichtleiste/B eschreibung: Hinw eise zu m Betrieb Folie nbindung 1_alle C omprima @ 5 07\mod_1500 467943576_78. docx @ 34873 98 @ @ 1
– When chamber film wrapping starts, it is necessary to continue collecting crop until the film
is caught by the round bale and the film roll is turning.
– For initial commissioning, a complete net roll should be used up if possible, and the round
bales should be tied with net. This way provides for previous removal of any sharp edges or
paint residues.
– If it is not possible to use net first for tying, any sharp edges must be removed manually,
see chapter "Removing paint and welding residues before commissioning".
– KRONE recommend not to use chamber film wrapping for straw bales to avoid the danger
of risk of condensation and resulting formation of mould.
– Have the machine tie the round bale with the appropriate film stretching, see chapter
"Checking the stretching of the inserted film".
– KRONE recommend 3.5 - 4 film layers for optimum chamber film wrapping, see chapter
"Number of film layers". The dryer the crops, the more film layers will be required.
– A machine with chamber film wrapping can still tie round bales with net. Please note that
the route of the net in the tying unit is different than the route of the film. Furthermore,
different settings are required for the wrapping material brake and the clamping lever, see
chapter Settings, "Setting the wrapping material brake" and "Locking/releasing the clamping
lever".
Pos: 48.99.49 / Layout Module /---------------Seitenumbruch---------------- @ 0\mod_1196 175311226_0. docx @ 4165 @ @ 1
To Next Page
Loading...
