Maintenance
212
Pos: 52.15.1 /Üb erschriften/Üb erschriften 2/A- E/A/Abstreifer einstellen @ 9\m od_122035 6915227_78.doc x @ 125784 @ 2 @ 1
13.5 Adjusting the Scraper
Pos: 52.15.2 /B A/Wartung/Run dballenpresse/Ab streifer/Steinabw eiser einstelle n/Abstreifer einst ellen_einleit ung-text_AL LE Comprima @ 468\mod_14 69699834379_ 78.docx @ 316 0264 @ @ 1
All scrapers on the deflection shafts in the bale chamber must be regularly checked and
adjusted.
Pos: 52.15.3 /B A/Wartung/Run dballenpresse/Ab streifer/Steinabw eiser einstelle n/Abstreifer einst ellen_bild_Com prima F V_CF CV @ 468\ mod_146969 5270560_78.doc x @ 3159626 @ @ 1
Fig.
Pos: 52.15.4 /B A/Wartung/Run dballenpresse/Ab streifer/Steinabw eiser einstelle n/Abstreifer einst ellen_te xt_Comprima F V @ 468\mod_ 1469695404949 _78.docx @ 3 159656 @ @ 1
Proceed as follows with all scrapers:
• Set the scraper (1) so that
– the inside distance (to the bale chamber) between deflection roll (2) and scraper (1) is
1-2 mm and
– the outside distance (to the side wall) between deflection roll (2) and scraper (1) is
0-1 mm.
Pos: 52.15.5 /L ayout Module /----------------Leerzeile-------------------- @ 240\mod _1395147357027 _0.docx @ 189 0988 @ @ 1
Pos: 52.15.6 /Üb erschriften/Zwisch enüberschrifte n/U-Z/Uml enkrollen ohne U mlenkwelle @ 468\mod_146 9699038973_7 8.docx @ 3160 140 @ @ 1
Deflection rolls without deflection shaft
Pos: 52.15.7 /A bkürzungen /Abkürz ungen sprac hneutral/Rundb allenpressen/Co mprima F @ 2 56\mod_1 397714206905_0. docx @ 196 2642 @ @ 1
Comprima F
Pos: 52.15.8 /B A/Wartung/Run dballenpresse/Ab streifer/Steinabw eiser einstelle n/Abstreifer einst ellen_Umlenkr ollen ohne U mlenkwelle_ei nleitung-text_ ALLE Compri ma @ 468\mod _1469703853 248_78.docx @ 31 60384 @ @ 1
All scrapers on the fixed deflection rolls must be regularly checked and adjusted. The following
image shows the position of the fixed deflection rolls (1) in the bale chamber at which scrapers
are mounted.
Pos: 52.15.9 /B A/Wartung/Run dballenpresse/Ab streifer/Steinabw eiser einstelle n/Abstreifer einstellen_Uml enkrollen ohn e Umlenkwelle_bil d_Comprima F V @ 468\mo d_146969912 2317_78.docx @ 3160170 @ @ 1
Fig.
Pos: 52.15.10 / BA/Wartung/Ru ndballenpresse/A bstreifer/Steina bweiser einst ellen/Abstreifer einstellen_Umle nkrollen ohne U mlenkwelle_te xt_Comprim a F V @ 468\ mod_146969981 4741_78.docx @ 3160233 @ @ 1
Proceed as follows with all scrapers:
• Set the scraper on the deflection rolls (2) so that the distance between deflection roll and
scraper is 0-0.5 mm.
Pos: 52.15.11 / Layout Module /---------------Seitenumbruch---------------- @ 0\mod_1196 175311226_0. docx @ 4165 @ @ 1
To Next Page
Loading...
