Krone EasyCut 2801 CV - Setting Deflector Sheets;Swath Sheets; Setting Swath Sheets

Settings
53
Pos: 22.40 /Übersc hriften/Überschri ften 3/K-O/Leitblec he/Schwadbleche einst ellen @ 288\mod_140990862 8274_78.docx @ 2280415 @ 3 @ 1
9.6.2 Setting Deflector Sheets/Swath Sheets
Pos: 22.41 /BA/Einste llungen/Mähwerke/Sc hwadbreite / Brei tablage/Gleichmäßig e Verteilung des Halmgu tes @ 288\mod_14101669171 73_78.docx @ 2283415 @ @ 1
In order to obtain a uniform distribution of cutting crops across the entire area, it may be
necessary depending on the operating conditions to readjust the deflector sheets (2, 3) and the
swath sheets (4).
Pos: 22.42 /BA/Einste llungen/Mähwerke/Sc hwadbreite / Brei tablage/Leitbleche ei nstellen @ 288\mod_1410 166794459_78.doc x @ 2283385 @ @ 1
Setting the deflector sheets
Pos: 22.43 /BA/Sic herheit/7. Gefahrenhin weise alt/Sicher heitshinweise am Anfang des Ka pitels beachten @ 101\ mod_1330611811687_7 8.docx @ 897943 @ @ 1
• Observe the safety instructions at the beginning of the section.
Pos: 22.44 /BA/Einste llungen/Mähwerke/Sc hwadbreite / Brei tablage/Einstellung d er Leitblech (2) zur Drehrichtung EC 2801/3201/36 00 CV @ 281\mod_14056791117 09_78.docx @ 2159774 @ @ 1
Deflector sheet (2)
• Unscrew ring nut (1).
• Move deflector sheet (2) in the desired position and tighten ring nut (1).
Pos: 22.45 /BA/Einste llungen/Mähwerke/Sc hwadbreite / Brei tablage/Einstellung d er Leitbleche (3) zur Drehrichtung EC 2801/320 1/3600 @ 281\mod_140567 2031538_78.docx @ 2159595 @ @ 1
Deflector sheet (3)
• Loosen palm knob (5).
• Move the deflector sheet (3) in the desired position and tighten palm knob (5).
Pos: 22.46 /BA/Einste llungen/Mähwerke/Sc hwadbreite / Brei tablage/Hinweis Kreuz griffe @ 59\mod_1297431 749350_78.doc x @ 558246 @ @ 1
Note
The star knobs may work loose due to vibrations, possibly resulting in the loss of the star
knobs, screws and swath plates.
• Manually tighten star knobs as tight as possible to ensure that they cannot work loose
during operation due to vibrations
Pos: 22.47 /Übersc hriften/Überschri ften 3/P-T/SSchwadblec he einstellen @ 288\mod _1409913891123_78.doc x @ 2281018 @ 3 @ 1
9.6.3 Setting Swath Sheets
Pos: 22.48 /BA/Einste llungen/Mähwerke/Sc hwadbreite / Brei tablage/Einstellung Sc hwadablage EC 2801/320 1/3600/ 3210 CV Schwadbl ech @ 288\mod_1409914266 190_78.docx @ 2281109 @ @ 1
Swathing
• Loosen ring nut (6) and swivel swath flap (4) into position (C).
• Tighten ring nut (6).
Pos: 22.49 /BA/Einste llungen/Mähwerke/Sc hwadbreite / Brei tablage/Einstellung Br eitablage EC 2801/320 1/3600/ 3210 CV Schwadblec h @ 284\mod_1407998381 276_78.docx @ 2246656 @ @ 1
Wide spreading
• Loosen ring nut (6) and swivel swath flap (4) into position (D).
• Tighten ring nut (6).
Pos: 22.50 /Layout Module /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1