Krone EasyCut 2801 CV - Setting Wide Distributor Plate

Settings
54
Pos: 22.51 /BA/Einste llungen/Mähwerke/Sc hwadbreite / Brei tablage/Breitvertei lerblech einstel len @ 60\mod_12978594205 39_78.docx @ 561604 @ 3 @ 1
9.6.4 Setting wide distributor plate
Pos: 22.52 /BA/Einste llungen/Mähwerke/Sc hwadbreite / Brei tablage/Breitvertei lerblech Bild @ 60\mod _1297859267403_78.doc x @ 561578 @ @ 1
2
EC-382-0
1
2
Fig. 33
Pos: 22.53 /BA/Sic herheit/7. Gefahrenhin weise alt/Sicher heitshinweise am Anfang des Ka pitels beachten @ 101\ mod_1330611811687_7 8.docx @ 897943 @ @ 1
• Observe the safety instructions at the beginning of the section.
Pos: 22.54 /BA/Einste llungen/Mähwerke/Sc hwadbreite / Brei tablage/Breitvertei lerblech einstel len Text @ 60\mod_12978595 89690_78.docx @ 561630 @ @ 1
For swathing set the wide distributor plate (2) all the way down.
For wide spreading the wide distributor plate can be adjusted individually to the amount of
forage.
To do this:
• Loosen the star knob (1) (right and left sides of machine)
• Swivel wide distributor plate (2) into the required position
• Tighten the star knobs (1)
Pos: 22.55 /BA/Einste llungen/Mähwerke/Sc hwadbreite / Brei tablage/Schwadklappe nverlängerung (opti onal) @ 131\mod_13475994 82412_78.doc x @ 1163175 @ @ 1
Swath Flap Extension (Optional)
Pos: 22.56 /BA/Einste llungen/Mähwerke/Sc hwadbreite / Brei tablage/Einstellung d er Schwadablage Bild EC28 0/320 CV / B 1000 CV Schwadklapp enverlängerung Bild @ 284\mod_1408004939190 _78.docx @ 2247220 @ @ 1
EC-527-0
Fig. 34
Pos: 22.57 /BA/Einste llungen/Mähwerke/Sc hwadbreite / Brei tablage/Schwadklappe nverlängerung eins tellen EC 2801/3201/360 0 CV Text @ 284\mod_1408006274 048_78.docx @ 2247311 @ @ 1
The swath width can additionally be set by means of the extension on the swath flaps.
To do this:
• Loosen palm knobs (1) (right-hand and left-hand side of the machine)
• Set the swath flap extension (2)
• Tighten palm knobs (1)
Pos: 22.58 /BA/Einste llungen/Mähwerke/Sc hwadbreite / Brei tablage/Hinweis Kreuz griffe @ 59\mod_1297431 749350_78.doc x @ 558246 @ @ 1
Note
The star knobs may work loose due to vibrations, possibly resulting in the loss of the star
knobs, screws and swath plates.
• Manually tighten star knobs as tight as possible to ensure that they cannot work loose
during operation due to vibrations
Pos: 22.59 /Layout Module /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1