Maintenance
65
Pos: 26.30.1 /Überschr iften/Überschr iften 2/K-O/Mäheran triebsgetriebe @ 9\mod_1 221045800746_78.doc x @ 131475 @ 2 @ 1
10.9 Mower Drive Gearbox
Pos: 26.30.2 /BA/W artung/Hinweis Ölstandsk ontrolle in Arbei tsstellung und in waagerec hter Stellung der Masc hine vornehmen @ 194\mo d_1383554973754_78. docx @ 1649577 @ @ 1
Note
Perform oil level check and oil change while the machine is in a horizontal position!
Pos: 26.30.3 /BA/W artung/Ölkontrolle_W echsel/Mähwerke/ Bild Mäherantriebsgetr iebe EC B 870 @ 240\mod_139513 2294978_78.doc x @ 1890002 @ @ 1
EC-041-2
Fig. 41
Pos: 26.30.4 /BA/W artung/Ölkontrolle_W echsel/Ölwechse l / Ölkontrolle:Legend e zu Grafik Kontrollsc hraube / Ablassschraube / Einfüllschraube @ 194\mo d_1383288259662_78. docx @ 1647783 @ @ 1
1) Inspection screw / control hole 2) Drain plug
3) Filler plug / oil filling hole
Pos: 26.30.5 /BA/W artung/Ölkontrolle_W echsel/Ölqualit ät /Ölmenge: siehe Kapite l Technische Daten @ 134\mod _1350483480921_78.do cx @ 1188085 @ @ 1
Oil Quality / Amount of Oil: Refer to Chapter Technical Data “Lubricants”
Pos: 26.30.6 /BA/W artung/Ölkontrolle_W echsel/Ölkontrol le / Ölwechsel Inter vall: siehe Kapitel War tung „Wartungstabelle“ @ 134\mod_13504836059 21_78.docx @ 1188115 @ @ 1
Interval for oil level check and oil change: refer to chapter Maintenance “Maintenance Table”
Pos: 26.30.7 /BA/W artung/Ölkontrolle_W echselÖlkontrol le NEU über Kontrollschr aube @ 140\mod_1355141753 680_78.docx @ 1244582 @ @ 1
Oil level check:
• Screw out inspection screw.
• Oil level up to control hole.
If the oil reaches the control hole:
• Screw in the inspection screw and tighten it securely.
If the oil does not reach the control hole:
• Screw out filler plug.
• Top up oil via oil filling hole until the control hole is reached.
• Screw in the inspection screw and the filler plug and tighten them securely.
Pos: 26.30.8 /BA/W artung/Ölkontrolle_W echselÖlwechsel NEU @ 140\mod_1355142057277_78. docx @ 1244610 @ @ 1
Oil change:
Collect escaping oil in a suitable container.
• Screw out oil drain plug and drain the oil.
• Screw out inspection screw and filler plug.
• Screw in oil drain plug and tighten it securely.
• Top up new oil via oil filling hole until the control hole is reached.
• Screw in the inspection screw and the filler plug and tighten them securely.
Pos: 26.30.9 /BA/W artung/Ölkontrolle_W echsel/Hinweis - Altöl or dnungsgemäß entsor gen @ 0\mod_1197008117002 _78.docx @ 15550 @ @ 1
Note
The used oil must be disposed of correctly
Pos: 26.31 /Layout Module /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1
To Next Page
Loading...
