KRONE ISOBUS-Terminal CCI 100
108
Pos: 61.46.41.3 /Über schriften/Überschr iften 3/K-O/Menü 4-2 Sen sortest Hand @ 34\mod_12 55414500878_78.doc x @ 322861 @ 3 @ 1
11.4.1 Menu 4-2 "Manual Sensor Test"
Pos: 61.46.41.4 /BA/ Info-Center/CCI -ISOBUS-Terminal/CCI- EasyCut/EasyCut B 1000/ Hauptmenüs/Haup tmenüs alte Ausführung/ Hauptmenüs 4 Service/ Menü 4-2 Sensortest Hand Bi ld @ 94\mod_1328012055775_ 78.docx @ 794145 @ @ 1
BPK40190_1
4-2
Fig. 68
Pos: 61.46.41.5 /BA/ Info-Center/CCI -ISOBUS-Terminal/CCI- Swadro/Swadro 2000/ Hauptmenüs/Hauptmen ü 4 Service/Menü 4-2 Sensor test Hand (2) Text @ 89\mod_132 1973827981_78.doc x @ 757513 @ @ 1
In the manual sensor test, the sensors that are installed on the machine are checked for errors.
In addition, the sensors can be correctly adjusted in the manual sensor test. There is no
guarantee the machine is working correctly until after the sensors have been adjusted.
Pos: 61.46.41.6 /BA/ Info-Center/CCI -ISOBUS-Terminal/CCI- Swadro/Swadro 2000/ Hauptmenüs/Hauptmen ü 4 Service/Menü 4-2 Sensor test Hand (3) Achtung Zapf welle darf nicht laufen @ 89\ mod_1321973934511_7 8.docx @ 757541 @ @ 1
Caution!
The P.T.O. shaft must not be turning during the sensor test.
Pos: 61.46.41.7 /BA/ Info-Center/CCI -ISOBUS-Terminal/CCI- Swadro/Swadro 2000/ Hauptmenüs/Hauptmen ü 4 Service/Menü 4-2 Sensor test Hand (4) Menü aufruf en @ 89\mod_1321974052838_ 78.docx @ 757569 @ @ 1
Calling the menu
Main menu 4 "Service" is called.
• Press the function key
or to enter menu 4-2 "Manual sensor test" . The
background of the selected symbol turns grey.
• Press function key
Selecting the sensor
• Press the function key
or to select the sensor.
The background of the selected symbol turns grey. The sensor test starts immediately.
Pos: 61.46.41.8 /BA/ Info-Center/Sensoren/ Diagnose Drucksen sor @ 115\mod_1339653067 227_78.docx @ 1011904 @ @ 1
Diagnostics Pressure Sensors
Pos: 61.46.41.9 /BA/ Info-Center/Sensoren/ Mögliche Sensore n (je nach Ausstattung der Masc hine) @ 19\mod_1238071 336628_78.docx @ 214010 @ @ 1
Possible sensors (depending on how the machine is equipped)
Pos: 61.46.41.10 /BA/ Info-Center/CCI -ISOBUS-Terminal/CCI -EasyCut/EasyCut B 100 0/Hauptmenüs/Haup tmenüs alte Ausführung/ Hauptmenüs 4 Service/ Diagnose Drucksensor Tabelle @ 118\mod_134199002 2225_78.docx @ 1030035 @ @ 1
B1
Front mowing unit up B2
Tank pressure
Pos: 61.46.41.11 /BA/ Info-Center/Sensoren/ Statusanzeigen/ Statusanzeigen Sensor (1,2) Druc kschwelle @ 118\mod_134199709973 2_78.docx @ 1048442 @ @ 1
State:
Pressure threshold is not reached
Pressure threshold is reached
Pos: 61.46.41.12 /Lay out Module /------ ---------Seitenu mbruch--------- ------- @ 0\mod_1196175311 226_0.docx @ 4165 @ @ 1
To Next Page
Loading...
