Krone EasyCut B 1000 CV - Gearbox for Top Roller Drive

Maintenance - Gearbox
187
Pos: 94.1 /Überschri ften/Überschrif ten 2/F-J/Getriebe für oberen Walzenantrieb @ 11\ mod_1223618840051_78. docx @ 148283 @ 2 @ 1
18.5 Gearbox for Top Roller Drive
Pos: 94.2 /Abkürzungen / CR-Ausführung @ 194\ mod_1383299073254_78. docx @ 1647987 @ @ 1
CR design
Pos: 94.3 /BA/War tung/Hinweis Ölstandskontr olle in Arbeitsste llung und in waagerecht er Stellung der Maschine vornehmen @ 194\mod_138355 4973754_78.doc x @ 1649577 @ @ 1
Note
Perform oil level check and oil change while the machine is in a horizontal position!
Pos: 94.4 /BA/War tung/Ölkontrolle_Wec hsel/Mähwerke/Bild Getriebe für oberen Walzen antrieb CR @ 194\mod_1383 559678635_78.docx @ 1649994 @ @ 1
EC-453-0
1
2
3
Fig. 119
Pos: 94.5 /BA/War tung/Ölkontrolle_Wec hsel/Ölwechsel / Ölkon trolle:Legende zu Grafi k Kontrollschraub e / Ablassschraube / Ei nfüllschraube @ 194\mod_13 83288259662_78.doc x @ 1647783 @ @ 1
1) Inspection screw / control hole 2) Drain plug
3) Filler plug / oil filling hole
Pos: 94.6 /BA/War tung/Ölkontrolle_Wec hsel/Ölqualität /Öl menge: siehe Kapitel Techni sche Daten @ 134\mod_135 0483480921_78.doc x @ 1188085 @ @ 1
Oil Quality / Amount of Oil: Refer to Chapter Technical Data “Lubricants”
Pos: 94.7 /BA/War tung/Ölkontrolle_Wec hsel/Ölkontrolle / Öl wechsel Intervall: si ehe Kapitel Wartung „W artungstabelle“ @ 134\ mod_1350483605921_78. docx @ 1188115 @ @ 1
Interval for oil level check and oil change: refer to chapter Maintenance “Maintenance Table”
Pos: 94.8 /BA/War tung/Ölkontrolle_Wec hsel/Ölkontrolle NE U über Kontrollschraube @ 140\mod_135514175368 0_78.docx @ 1244582 @ @ 1
Oil level check:
• Screw out inspection screw.
• Oil level up to control hole.
If the oil reaches the control hole:
• Screw in the inspection screw and tighten it securely.
If the oil does not reach the control hole:
• Screw out filler plug.
• Top up oil via oil filling hole until the control hole is reached.
• Screw in the inspection screw and the filler plug and tighten them securely.
Pos: 94.9 /BA/War tung/Ölkontrolle_Wec hsel/Ölwechsel NEU @ 140\ mod_1355142057277_78. docx @ 1244610 @ @ 1
Oil change:
Collect escaping oil in a suitable container.
• Screw out oil drain plug and drain the oil.
• Screw out inspection screw and filler plug.
• Screw in oil drain plug and tighten it securely.
• Top up new oil via oil filling hole until the control hole is reached.
• Screw in the inspection screw and the filler plug and tighten them securely.
Pos: 94.10 /BA/W artung/Ölkontrolle_Wec hsel/Hinweis - Altöl ordn ungsgemäß entsorgen @ 0\ mod_1197008117002_78. docx @ 15550 @ @ 1
Note
The used oil must be disposed of correctly
Pos: 95 /Layout Modu le /---------------Seitenumbruch---------------- @ 0\mod_11961753112 26_0.docx @ 4165 @ @ 1