Krone EasyCut B 1000 CV - Switching Terminal On;Off (Machine Connected)

KRONE ISOBUS-Terminal CCI 100
55
Pos: 61.30 /Überschr iften/Überschri ften 3/A-E/E/Ein- Ausschalten des Terminals bei angeschlossener Masc hine @ 43\mod_12748662 10140_78.docx @ 387724 @ 3 @ 1
8.2.7 Switching the terminal on / off when the machine is connected
Pos: 61.31 /Überschr iften/Überschrif ten 4/P-T/Startbild @ 50\ mod_1287737794484_78. docx @ 475246 @ 3 @ 1
8.2.7.1 Start screen
Pos: 61.32 /BA/Inf o-Center/CCI-I SOBUS-Terminal/CCI-Easy Cut/EasyCut B 1000/Ein- Ausschalten Startbi ld mit angeschlossen er Maschine EasyCut B 1000 @ 93\ mod_1327494758232_7 8.docx @ 790333 @ @ 1
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11F11
F12
ESC
CC000516
1
Fig. 30
Pos: 61.33 /BA/Inf o-Center/CCI-I SOBUS-Terminal/Ein- Aussc halten des Terminal´s/ Hinweis Bevor Sie das Ter minal zum ersten Mal... @ 43\mod_1273657536203 _78.docx @ 384008 @ @ 1
Note
Before switching the terminal on for the first time make sure that the connections on the device
are fastened right and securely.
By pressing and holding (for approx. 2 sec.) the key (1)
(ON/OFF) the terminal will be
switched on or off.
Pos: 61.34 /BA/Inf o-Center/CCI-I SOBUS-Terminal/Ein- Ausscha lten des Terminal´s/ Hinweis Vor der Erstben utzung @ 43\mod_12748528 23031_78.docx @ 387615 @ @ 1
Note - Prior to first use
When switching on for the first time the configuration of the specific menu of the machine is
uploaded into the terminal. The loading may take a few minutes. The configuration will be
saved on the memory of the terminal.
Pos: 61.35 /BA/Inf o-Center/CCI-I SOBUS-Terminal/Ein- Ausscha lten des Terminal´s/ Ein- Ausschalten nac h dem Ladevorgang wird im Di splay das „Straßenbild“ angezeigt. @ 43\mod_1274 853526062_78.doc x @ 387639 @ @ 1
• The “start-up screen” is shown in the display after the loading process
The terminal is now ready for operation.
Pos: 61.36 /BA/Inf o-Center/CCI-I SOBUS-Terminal/Ein- Ausscha lten des Terminal´s/ Umschalten Straßenbi ld auf Grundbild Front mähwerk heben/senken Mäh werke heben/senke @ 93\ mod_1327496323471_78. docx @ 790419 @ @ 1
• Pressing the function key invokes either the 'Raise/Lower front mowing unit' basic
dialogue or the 'Raise/Lower mowing units' basic dialogue depending on the position of the
lateral mowing units.
Pos: 61.37 /BA/Inf o-Center/CCI-I SOBUS-Terminal/CCI-Easy Cut/Softkeys für di e FunktionstastenFunk tionstasten F1 bis F 12 Bild Hand Grundbild Frontmäh werk / Mähwerke (2014-10- 06 15:13:39) @ 92\mod_1327 060778263_78.doc x @ 786202 @ @ 1
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11F11
F12
40
100
%
100
%
cm
40
cm
0.0
1
50
%
50
%
R
L
CC000503
Fig. 31
'Raise/Lower front mowing unit' basic
dialogue
'Raise/Lower mowing units' basic dialogue
Pos: 61.38 /Layout Module /---------------Seitenumbruc h---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1