Krone EasyCut B 1000 CV - Lowering All Mowing Units from Headland Position to Working Position; Lowering Individual Mowing Units Inching with the Key

KRONE ISOBUS CCI 100 Terminal / manual mode
70
Pos: 61.39.7.9 /BA/ Info-Center/CCI -ISOBUS-Terminal/CCI- EasyCut/EasyCut B 1000/ Grundbild Mähwerke hebe n/senken tastendGrun dbild Mähwerke heben/ senken tastend (2014- 10-07 14:40:31) @ 118\mod_1 341553430820_78. docx @ 1025129 @ @ 1
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11F11
F12
CC000601
40
100
%
100
%
cm
40
cm
0.0
1
50
%
50
%
R
L
Fig. 41
Pos: 61.39.7.10 /BA/ Info-Center/CCI -ISOBUS-Terminal/CCI- EasyCut/EasyCut B 1000/ Grundbild Mähwerke heb en/senkenAbsenken a ller Mähwerke von Vorgewend estellung in Arbei tsstellung abhängig vom Menü 1-7 (2014-10-07 13: 33:07) @ 180\mod_1375874387 618_78.docx @ 1541642 @ 3 @ 1
9.4.2 Lowering All Mowing Units from Headland Position to Working Position
Lowering the lateral mowing units to the front mowing unit depends on the set mode in menu 1-
7 “Setting Manual Control/Distance Control/Time Control”.
In mode 1 manual control
• Press and hold the function key for
to lower the front mowing unit.
• Release the function key for
to lower the lateral mowing units.
In mode 2 time control and mode 3 distance control
• Press and release the function key for
to lower the front mowing unit and the lateral
mowing units.
The lateral mowing units are lowered after the set time delay and the set distance have been
reached.
Note
The lateral mowing units are lowered directly into working position if there is no front mowing
unit installed.
Pos: 61.39.7.11 /BA/ Info-Center/CCI -ISOBUS-Terminal/CCI- EasyCut/EasyCut B 1000/ Grundbild Mähwerke heb en/senken tastendEi nzelne Mähwerke tast end absenken (2014-10-07 1 4:49:11) @ 118\mod_134155 5052936_78.doc x @ 1025216 @ 3 @ 1
9.4.3 Lowering Individual Mowing Units Inching With the Key
Preselect the mowing units to be lowered by using the appropriate function keys for
, ,
(the preselected mowing units are highlighted in colour ( , , ).
Lower the preselected mowing units by pressing and holding function key for
. The mowing
units are lowered as long as the function key is activated.
Pos: 61.39.7.12 /BA/ Info-Center/CCI -ISOBUS-Terminal/CCI- EasyCut/EasyCut B 1000/ Grundbild Mähwerke heb en/senken tastend/ Hinweis: Schwimmste llung für die Mähwerke ist auf gehoben @ 118\mod_13415 59336334_78.doc x @ 1025364 @ @ 1
Note
Mowing units must not be in float position anymore.
Pos: 61.39.7.13 /Layout Module /---------------Seitenumbruch---------------- @ 0\ mod_1196175311226_0.doc x @ 4165 @ @ 1