Krone EasyCut B 1000 CV - Hydraulic System Basic Dialogue

KRONE ISOBUS CCI 100 Terminal / manual mode
76
Pos: 61.39.13.1 /Über schriften/Überschr iften 2/F-J/Gr undbild Hydrauliksyste m @ 93\mod_1327061329082_7 8.docx @ 786342 @ 2 @ 1
9.7 Hydraulic system basic dialogue
Pos: 61.39.13.2 /BA/ Info-Center/CCI -ISOBUS-Terminal/CCI- Swadro/Swadro 1400 Gefahr Schnellstop (2014- 10-07 11:55:57) @ 56\mod_1 295362873734_78.doc x @ 542364 @ @ 1
DANGER! - Before swivelling the machine, ensure that nobody is within the swivel
range.
Effect: Danger to life or serious injuries.
• Instruct persons to leave the danger zone.
• If required, switch off the machine immediately.
• If there is an imminent danger, press the function key for to stop all functions which
are currently being performed.
Pos: 61.39.13.3 /BA/ Info-Center/CCI -ISOBUS-Terminal/CCI- EasyCut/EasyCut B 1000/ Grundbild Hydauliksy stemGrundbild Hydrauliksystem Bild ( 2014-10-07 16:40:29) @ 93\mod_1327396349202 _78.docx @ 787980 @ @ 1
Fig. 44
Pos: 61.39.13.4 /BA/ Info-Center/CCI -ISOBUS-Terminal/CCI- EasyCut/EasyCut B 1000/ Grundbild Hydauliksy stem/Seitenmäh werke abkuppeln allge mein @ 93\mod_132740087203 2_78.docx @ 788479 @ @ 1
Before you disconnect the lateral mowing units from the tractor, depressurise the hydraulic
system completely so as to avoid difficulties when reconnecting the machine to the tractor the
next time.
Pos: 61.39.13.5 /BA/ Info-Center/CCI -ISOBUS-Terminal/CCI- EasyCut/EasyCut B 1000/ Grundbild Hydauliksy stemGrundbild Hydrauliksystem Einf ührtext (2014-10- 07 16:46:27) @ 118\mod_13415 65010839_78.doc x @ 1025656 @ @ 1
The basic screen “Hydraulic System” does only appear if both lateral mowing units are in
working position or in transport position (locked).
Pos: 61.39.13.6 /BA/ Info-Center/CCI -ISOBUS-Terminal/CCI- EasyCut/EasyCut B 1000/ Grundbild Hydauliksy stem/Aufrufen Grundbi ld Hydrauliksy stem aufrufen F9 @ 118\mod_1 341564650842_78. docx @ 1025598 @ @ 1
Displaying the basic hydraulic system dialogue
The 'Hydraulic system' basic dialogue is indicated on the terminal via the
symbol.
Pos: 61.39.13.7 /BA/ Info-Center/CCI -ISOBUS-Terminal/CCI- EasyCut/EasyCut B 1000/A nzeigenbereic he Display Handbetrieb/Auf rufen der Grundbild er F9 @ 117\mod_13413790799 97_78.docx @ 1022995 @ @ 1
• Press function key basic screen ( , , , , , ) until the
desired basic screen is displayed in the terminal
Pos: 61.39.13.8 /BA/ Info-Center/CCI -ISOBUS-Terminal/CCI- EasyCut/EasyCut B 1000/ Grundbild Hydauli ksystemHydrauliksy stem drucklos schalten (2014-10-07 16:48: 43) @ 118\mod_1341564 357886_78.docx @ 102556 9 @ @ 1
Pressing the function key for depressurises the hydraulic system.
All valves are opened for several seconds.
Pos: 61.40 /Layout Module /---------------Seitenumbruc h---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1