Krone EasyCut B 870 CV Collect - Page 108

130 pages

To Next Page

To Previous Page

Maintenance – lubrication chart

108

Pos: 159.14 /Abkürzu ngen /Abkürzungen sprac hneutral/EasyCut/ EasyCut B 870 CR @ 230\mod_13933 40484210_0.doc x @ 1844449 @ @ 1

EasyCut B 870 CR

Pos: 159.15 /BA/W artung/Mähwerke/EasyCut / AM Mähwerke/Schmierpl äne/Schmierplan EC B 870 C R @ 230\mod_1393340578377_7 8.docx @ 1844508 @ @ 1

ECB00101

Fig. 65

Main Page

Table of Contents3
Foreword7
To this Document8
Validity8
Direction Information8
Identifying Symbols in the Operating Instructions8
Identification of the Hazard Warnings8
Safety9
Purpose of Use9
Intended Use9
Service Life of the Machine9
Safety Instructions and Accident Prevention Regulations10
Personnel Qualification and Training11
Dangers in Case of Non-Compliance with the Safety Instructions11
Safety-Conscious Work Practices11
Attached Devices12
PTO Operation12
Hydraulic System13
Maintenance14
Unauthorised Conversion/Modification and Spare Parts Production14
Inadmissible Modes of Operation14
Working in the Vicinity of Power Transmission Lines14
Machine Description16
Machine Overview16
Identification Plate18
Information Required for Questions and Orders18
Contact18
Introduction19
Re-Ordering the Adhesive Safety and Information Labels19
Affixing the Adhesive Safety and Information Labels19
Position of the Adhesive Safety Stickers on the Machine20
Technical Data of the Machine28
Technical Data28
Consumables32
Filling Quantities and Lubrication Designations for Gearboxes32
Control and Display Elements33
Commissioning36
First Installation36
Special Safety Instructions36
Check List for Initial Operation37
Adapting to the Tractor38
Clutching Points38
PTO Shaft40
Length Adjustment40
Checking Cross Conveyor Belt Right / Left for Firm Attachment42
Start-Up43
Mounting Onto the Tractor43
Hydraulics44
Special Safety Instructions44
Connecting the Hydraulic Lines44
Connecting the Operation45
Lighting46
Lighting Connection46
PTO Shaft47
Special Safety Instructions47
Install the PTO Shaft47
Intermediate PTO Shaft48
Swivelling Parking Support into Transport Position48
Driving and Transport49
Switching from Working Position to Transport Position49
Operation51
Before Mowing51
Mowing51
Folding down the Safety Device52
Adjusting the Lateral Suspension Arm53
Lowering Mowing Units53
From Transport Position to Headland Position53
Headland Position54
From Headland Position to Transport Position55
Cross Conveyor Operation56
General56
Speed Control of Transport Belts56
Swivelling Parking Support into Transport Position57
Detaching the Machine58
Parking59
Settings60
Adjusting the Cutting Height60
Adjusting the Guards61
Lateral Guards61
Setting of the Pole Protection Mechanism62
Adjusting the Tedder Speed63
Adjusting the Conditioner Plate64
Adjustment for Swathing65
Wide Spreading66
Setting Wide Distributor Plate67
Wide Spreading with the "Cross Conveyor" Option68
Adjust Locking70
Setting the Distance of the Rollers71
Setting Conveyor Belt72
Moving the Cross Conveyor74
Bar on Cross Conveyor Is Bent74
Maintenance75
Test Run75
Spare Parts75
Maintenance Table76
Tightening Torques77
Metric Thread Screws with Control Thread77
Metric Thread Screws with Fine Thread78
Metric Thread Screws with Countersunk Head and Hexagonal Socket78
Deviating Torque79
Rotary Hub with Shear Fuse (Optional)80
After Shearing off82
Maintenance - Gearbox84
Main Gearbox84
Mower Drive Gearbox85
Angular Gearbox86
Top Part86
Angular Gearbox87
Bottom Part87
Gearbox for Top Roller Drive88
Oil Level Check and Oil Change on the Cutter Bar89
Oil Change89
Checking the Oil Level89
Maintenance - Blade Changing90
Checking the Cutter Blades and Blade Holder90
Cutter Blades91
Blade Screw Connection92
Blade Quick-Fit Device92
Periodical Inspection of the Leaf Springs93
Periodical Inspection of the Cutting Discs / Blade Drums94
Abrasion Limit95
Blade Changing on Cutting Discs96
Blade Screw Connection97
Blade Quick-Fit Device98
Replacing the Linings99
Maintenance - Hydraulic System100
Oil Tank100
Checking the Oil Level101
Oil Change101
Hydraulic System102
Replacing the Hydraulic Oil Filter102
Maintenance - Lubrication Chart103
Special Safety Instructions103
PTO Shaft103
Lubrication Chart104
Maintenance - Cleaning112
Cleaning the Cross Conveyor Belts112
Placing in Storage114
Before the Start of the New Season115
Special Safety Instructions115
Test Run115
Friction Clutch116
Special Equipment117
Special Safety Instructions117
Adjusting Skids117
Disposal of the Machine118
Appendix119
Electrical Circuit Diagram119
Index120

Krone EasyCut B 870 CV Collect - Page 108

Table of Contents

Related product manuals