Krone Swadro TS 620 - Setting Headland Position Height

Settings
101
Pos: 40.16.1 /Überschr iften/Überschr iften 2/F-J/HHöhe der Vor gewendestellung eins tellen @ 243\mod_1395741 004513_78.doc x @ 1906475 @ 2 @ 1
11.5 Setting the Height of the Headland Position
Pos: 40.16.2 /BA/Ei nstellungen/Schwader /Höhe der Vorgewendes tellung einstellen Sei tenschwader_Ein leitung @ 244\mod_1395757 694093_78.docx @ 1907411 @ @ 1
The height of the both rotors in headland position is set via timing discs.
On the front rotor, the setting is made via the rear timing disc.
Pos: 40.16.3 /Layout Module /----------------Leerzeile-------------------- @ 240\mod_1395147357027_0.docx @ 1890988 @ @ 1
Pos: 40.16.4 /Überschr iften/Zwischenü berschriften/U- ZVorderer Kreisel @ 244\ mod_1395757001698_78. docx @ 1907293 @ @ 1
Front rotor
Pos: 40.16.5 /BA/Ei nstellungen/Schwader /Höhe der Vorgewendes tellung einstellen Sei tenschwader_Vorder er Kreisel_Bild @ 243\ mod_1395735899572_7 8.docx @ 1905884 @ @ 1
2
SW9070126
Fig. 59
Pos: 40.16.6 /BA/Ei nstellungen/Schwader /Höhe der Vorgewendes tellung einstellen Sei tenschwader_Vorder er Kreisel_Text @ 244\ mod_1395756909787_ 78.docx @ 1907264 @ @ 1
The height of headland position is set by adjusting the timing disc (2).
To do this:
• Loosen the screws on the timing disc (2).
• Move timing disc in the oblong holes.
Moving the timing disc clockwise: greater height of the swing outriggers in headland
position.
Moving timing disc anti-clockwise: lower height of the swing outriggers in headland
position.
Pos: 40.16.7 /Überschr iften/Zwischenü berschriften/F- JHinterer Kreisel @ 244\m od_1395757042042_78.d ocx @ 1907352 @ @ 1
Rear rotor
Pos: 40.16.8 /BA/Ei nstellungen/Schwader /Höhe der Vorgewendes tellung einstellen Sei tenschwader_Hin terer Kreisel_Bild @ 243\ mod_1395735954775_7 8.docx @ 1905913 @ @ 1
2
SW9070127
Fig. 60
Pos: 40.16.9 /BA/Ei nstellungen/Schwader /Höhe der Vorgewendes tellung einstellen Sei tenschwader_Hin terer Kreisel_Text @ 246\ mod_1396338374965_7 8.docx @ 1921546 @ @ 1
The height of headland position is set by adjusting the timing disc (2).
To do this:
• Loosen the screws on the timing disc (2).
• Move timing disc in the oblong holes.
Moving the timing disc anti-clockwise: larger height of the swing outriggers in headland
position.
Moving the timing disc clockwise: lower height of the swing outriggers in headland
position.
Pos: 40.17 /Layout Module /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0. docx @ 4165 @ @ 1