Krone Swadro TS 620

To Next Page

To Previous Page

Maintenance - Gearbox

126

Pos: 42.37.3.10 /Layout Module /---------------Seitenumbruch--------------- - @ 0\mod_1196175311226_0.doc x @ 4165 @ @ 1

Main Page

1 Table of Contents3
2 To this Document7
- Validity7
- Re-Ordering7
- Further Applicable Documents7
- Target Group of this Document7
- How to Use this Document7
3 Safety12
- Intended Use12
- Service Life of the Machine12
- Basic Safety Instructions12
- Safety Routines24
- Safety Stickers on the Machine26
- Safety Equipment31
4 Machine Description34
- Machine Overview34
- Identification Plate36
- Information Required for Questions and Orders36
  - Contact36
5 Technical Data of the Machine38
- Technical Data38
- Consumables50
- Tyres50
- Airborne Sound Emission50
- Ambient Temperature50
6 Control and Display Elements51
7 Commissioning53
- First Installation53
- Connect the Machine to the Tractor54
- PTO Shaft54
  - Length Adjustment54
- Regulating Direction of Travel55
- Checking / Setting the Distance between Tine Arm and Lifting Cylinder56
- Basic Setting of Rotor Inclination57
8 Start-Up58
- Preparations on Tractor59
  - Adjusting the Lower Suspension Arms59
- Connect the Machine to the Tractor60
- Height of Tractor Lower Suspension Arms61
- Install the PTO Shaft62
- Connecting the Hydraulic Lines64
- Lighting Connection65
- Connecting the Operation66
- Laying the Operating Cable66
- Using the Safety Chain67
9 Driving and Transport69
- Preparations for Road Travel70
- Driving on Slopes71
- Protecting the Tine Tips (Transport Position and Rotary Rake Switched Off)71
- Parking72
10 Operation73
- Removing the Tine Protections from the Tine Tips74
- Lowering Outrigger Arms into Working Position75
- Swivel Tine Arms to Working Position76
  - For Design with Collapsible Tine Arm77
- Move the Hoop Guards to the Working Position78
- Setting the Rear Swath Cloth79
- Setting Front Swath Cloth81
  - Swivelling down Front Swath Cloth81
  - Swivelling up Front Swath Cloth81
- Setting the Working Height82
  - With Electrical Rotor Height Adjustment Version83
- Switching from One Side Swath to Two Individual Swaths (Optional)84
  - Changing from Single Swathing to Double Swathing84
  - Changing from Double Swathing to Single Swathing84
- Travelling Speed und Drive Speed85
- Swathing85
- Move the Hoop Guards to Transport Position86
- Swivelling Tine Arms into Transport Position87
  - With Rigid Tine Arms Design87
  - For Design with Collapsible Tine Arm88
- Swivelling Parking Support into Transport Position89
- Raising Outrigger Arms into Transport Position90
11 Settings91
- Setting the Rotor Inclination92
- Fixing the Trailing Guide Wheels98
- Adjustable Throttles99
- Setting the Lifting Delay100
- Setting the Height of the Headland Position101
- Calibrating the Sensor - with Electrical Rotor Height Adjustment Design102
12 Maintenance103
- Spare Parts103
- Compensation Spring(S)103
- Maintenance Table104
- Tightening Torques105
- Deviating Tightening Torques MA (Nm)108
  - Testing the Screws on the Tines108
  - Tightening Torque of the Wheels on the Chassis108
- Tyres110
  - Checking and Maintaining Tyres111
- Replacing the Tine Arms (in Case of Repair)112
- Replacing the Tines (in Case of Repairs)114
13 Maintenance - Lubrication116
- Lubrication Points on the Universal Shafts116
- Lubrication Points on the Machine118
14 Maintenance - Hydraulic System123
15 Maintenance - Gearbox124
- Rotor Gear / Rotor Housing124
- Distributor Gearbox Front125
- Distributor Gearbox Rear127
16 Special Equipment128
- Tine Loss Safeguard128
- Chain for Height Restriction of Suspension Arms129
17 Placing in Storage130
- At the End of the Harvest Season130
- Before the Start of the New Season131
18 Malfunctions - Causes and Remedies132
- Special Safety Instructions132
19 Disposal of the Machine134
20 Appendix135
- Circuit Diagrams of the Hydraulic System135
- Circuit Diagram140
21 Index146

Krone Swadro TS 620 - Page 126

Table of Contents

Related product manuals