KTM RC 250 R - Auxiliary Substances and Cleaners; Air Filter Cleaner; Air Filter Oil; Chain Cleaner

101 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

23 WIRING DIAGRAM 93

Components:

P_RB

Pressure rear brake sensor

SUS_R

Suspension rear sensor

main_relais

Power relay

light

Rear light

Laptrigger

12V power supply for laptimer

VR

Wheel speed rear

Fuelpump

Fuel pump

PickUp

Pick-up sensor

Table of Contents

Default Chapter4
- Table of Contents4
1 Means of Representation6
- Symbols Used6
- Formats Used6
2 Safety Advice7
- Use Definition - Intended Use7
- Degrees of Risk and Symbols7
- Safe Operation7
- Protective Clothing8
- Work Rules8
- Environment8
- Owner's Manual8
3 Important Notes9
- Operating and Auxiliary Substances9
- Spare Parts, Accessories9
- Service9
- Figures9
- Customer Service9
4 View of Vehicle10
- View of Vehicle, Front Left Side (Example)10
- View of Vehicle, Rear Right Side (Example)11
5 Serial Numbers12
- Vehicle Identification Number12
- Engine Number12
- Fork Part Number12
- Shock Absorber Part Number12
- Steering Damper Part Number12
6 Controls13
- Clutch Lever13
- Hand Brake Lever13
- Throttle Grip13
- Ignition Switch13
- Tail Light Switch13
- Map-Select Switch14
- Launch-Control Button14
- Pit-Limiter Button14
- Quick Shifter Switch14
- Indicator Lamps14
- Combination Instrument 1/216
- Combination Instrument 2/218
- Opening the Filler Cap19
- Closing the Filler Cap19
- Idle Speed Adjusting Screw20
- Shift Lever20
- Foot Brake Lever20
7 Preparing for Use21
- Advice on First Use21
- Running the Engine in21
8 Riding Instructions22
- Checks and Maintenance Measures When Preparing for Use22
- Starting22
- Transport23
- Refueling23
9 Service Schedule25
- Service Schedule 13,500 Rpm25
- Maintenance Work (as an Additional Order) 13,500 Rpm25
- Service Schedule 14,000 Rpm26
- Maintenance Work (as an Additional Order) 14,000 Rpm27
10 Tuning the Chassis29
- Adjusting the Compression Damping of the Fork29
- Adjusting the Rebound Damping of the Fork29
- Adjusting the Spring Preload of the Fork29
- Fork Offset30
- Adjusting the Fork Offset30
- Compression Damping of the Shock Absorber31
- Adjusting the Low-Speed Compression Damping of the Shock Absorber32
- Adjusting the High-Speed Compression Damping of the Shock Absorber32
- Adjusting the Rebound Damping of the Shock Absorber32
- Adjusting the Spring Preload of the Shock Absorber33
- Steering Damper33
- Adjusting the Steering Damper34
- Vehicle Level34
- Adjusting Front Vehicle Level34
- Adjusting the Vehicle Level at the Rear36
11 Service Work on the Chassis37
- Raising the Rear of the Motorcycle with Lifting Gear37
- Removing the Rear of Motorcycle from the Lifting Gear37
- Raising the Front of the Motorcycle with Lifting Gear37
- Taking the Motorcycle off of the Front Lifting Gear37
- Removing the Air Filter38
- Cleaning the Air Filter38
- Installing the Air Filter39
- Removing the Engine Cowl40
- Installing the Engine Cowl40
- Removing the Front Fairing40
- Installing the Front Fairing41
- Removing the Fuel Tank41
- Installing the Fuel Tank42
- Checking the Fuel Overflow Reservoir43
- Emptying the Fuel Overflow Reservoir43
- Checking the Coolant Overflow Reservoir44
- Emptying the Coolant Overflow Reservoir44
- Checking for Chain Dirt44
- Cleaning the Chain44
- Checking the Chain Tension45
- Adjusting the Chain Tension45
- Checking the Rear Sprocket and Engine Sprocket46
12 Brake System47
- Adjusting the Basic Position of the Hand Brake Lever47
- Checking Brake Discs47
- Checking the Front Brake Fluid Level47
- Adding Front Brake Fluid48
- Checking the Front Brake Linings48
- Changing the Front Brake Linings49
- Checking Rear Brake Fluid Level50
- Adding Rear Brake Fluid51
- Checking the Rear Brake Linings52
- Changing the Rear Brake Linings52
13 Wheels, Tires54
- Removing the Front Wheel54
- Installing the Front Wheel54
- Removing the Rear Wheel54
- Installing the Rear Wheel55
- Checking the Rear Hub Rubber Dampers56
- Checking the Tire Condition56
- Checking the Tire Pressure57
14 Electrical System58
- Removing the Battery58
- Installing the Battery58
- Recharging the Battery58
- Changing the Main Fuse59
15 Data Recording61
- Data Recording Connector AP61
- Expansion Sensors61
- Extension Sensors Connector CY61
- CAN Matrix62
16 Cooling System63
- Checking the Coolant Level63
- Draining the Coolant63
- Refilling with Coolant64
17 Tuning the Engine65
- Checking the Play in the Throttle Cable65
- Adjusting the Play in the Throttle Cable65
- Adjusting the Idle Speed66
- Quick Shifter66
- Checking the Position of the Quick Shifter66
- Positioning the Quick Shifter67
18 Service Work on the Engine68
- Checking the Engine Oil Level68
- Changing the Engine Oil and Oil Filter, Cleaning the Oil Screen68
- Adding Engine Oil70
- Removing the Engine70
- Installing the Engine72
19 Ems Components75
- Engine Control Unit75
- Adjusting the Throttle Position Sensor75
- Adjusting the Gear Position Sensor76
20 Cleaning, Care78
- Cleaning the Motorcycle78
21 Storage79
- Preparing for Use after Storage79
22 Technical Data80
- Engine80
- Engine Tightening Torques80
- Capacities82
- Engine Oil82
- Coolant82
- Fuel82
- Chassis82
- Electrical System82
- Tires83
- Fork83
- Shock Absorber83
- Chassis Tightening Torques83
- Wiring Diagram86

Related product manuals

Preview: KTM 2016 RC 250

KTM 2016 RC 250

Preview: KTM Freeride 250 R

KTM Freeride 250 R

Preview: KTM Freeride 250 R EU

KTM Freeride 250 R EU

Preview: KTM 2014 Freeride 250 R

KTM 2014 Freeride 250 R

Preview: KTM RC 125 2019

KTM RC 125 2019

Preview: KTM RC 390 2018

KTM RC 390 2018

Preview: KTM RC 390 2020

KTM RC 390 2020

KTM RC 125 2022

Preview: KTM 2015 RC 390 EU

KTM 2015 RC 390 EU

Preview: KTM RC 125 EU 2015

KTM RC 125 EU 2015

KTM 2015 RC 390 JP