Why KTM RC 390 2018 Motorcycle engine has too little power?
If your KTM Motorcycle engine has too little power, start by checking if the air filter is dirty and change it if necessary. Also, check the fuel pressure if the fuel filter is very dirty.
What to do if the ABS warning lamp lights up on KTM RC 390 2018 Motorcycle?
If the ABS warning lamp lights up on your KTM Motorcycle, it could be due to several reasons. First, check the ABS fuses and replace them if they are blown. It could also indicate a large difference in wheel speeds between the front and rear wheels; in this case, stop the motorcycle, switch off the ignition, and then restart it. Finally, a malfunction in the ABS could be the reason.
Why KTM RC 390 2018 engine does not crank when the electric starter button is pressed?
If your KTM Motorcycle's engine won't crank when you press the electric starter, several things could be happening. First, ensure you are following the correct start procedure. If that's not the issue, check if the battery is discharged and recharge it if necessary. Also, examine fuses 1, 3, 4, and 7, replacing any that are blown. Finally, verify the ground connection is secure.
What to do if my KTM Motorcycle engine turns but does not start?
If your KTM Motorcycle engine turns but does not start, ensure you are following the correct start procedure. There may also be a fault in the fuel injection system.
What to do if KTM RC 390 2018 Motorcycle has high oil consumption?
If your KTM Motorcycle has high oil consumption, it could be because the engine oil is too thin (low viscosity). In this case, change the engine oil and oil filter and clean the oil screens.
What to do if KTM RC 390 2018 Motorcycle engine turns but does not start?
If the engine of your KTM Motorcycle turns but does not start, ensure you are following the correct start procedure.
What to do if KTM RC 390 2018 Motorcycle engine overheats?
If your KTM Motorcycle is overheating, it might be due to foam formation in the cooling system. In this case, drain the coolant and then refill/bleed the cooling system. Other potential causes include a defective thermostat, a blown fuse 5 (so replace the fuses), or a defect in the radiator fan system, so check the radiator fan system.
What causes high oil consumption in KTM RC 390 2018?
High oil consumption in your KTM Motorcycle could be due to a bent engine vent hose; ensure the vent hose is routed without bends, or replace it if needed. Another cause could be an engine oil level that is too high, so check the engine oil level.
How to troubleshoot discharged battery on KTM RC 390 2018 Motorcycle?
A discharged battery in your KTM Motorcycle could be due to the ignition being left on while parked, so avoid leaving the ignition on when the vehicle is parked. Alternatively, the battery may not be charging due to an issue with the alternator. In this case, check the charging voltage and the open-circuit current.
General| Displacement | 373.2 cc |
|---|---|
| Bore x Stroke | 89 mm x 60 mm |
| Compression Ratio | 12.6:1 |
| Torque | 36 Nm @ 7, 000 rpm |
| Transmission | 6-speed |
| Cooling | Liquid cooled |
| Rear Suspension | WP monoshock |
| Front Tire | 110/70 ZR17 |
| Rear Tire | 150/60 ZR17 |
| Seat Height | 820 mm |
| Ground Clearance | 178.5 mm |
| Fuel Tank Capacity | 10 liters |
| Dry Weight | 147 kg |
| Engine Type | Single Cylinder, 4-Stroke |
| Power | 43 hp (32 kW) @ 9, 000 rpm |
| Fuel System | Electronic Fuel Injection |
| Frame | Steel trellis frame |
| Front Suspension | WP upside-down Ø 43 mm |
| Front Brake | 320 mm disc |
| Rear Brake | 230 mm disc, single-piston caliper |
| ABS | Two-channel Bosch 9MB ABS |
Provides essential instructions for safe operation and highlights important labels.
Explains the different levels of risk (Danger, Warning, Caution, Note) and their symbols.
Details crucial safety aspects for operating the vehicle, including rider fitness.
Describes the location and function of the emergency OFF switch.
Explains the ignition and steering lock positions and functions.
Explains the various indicator lamps on the instrument cluster and their meanings.
Offers crucial safety advice and checks before the first ride.
Explains the procedure and limits for running in the engine.
Lists essential checks to ensure the vehicle is roadworthy before riding.
Details the procedure for starting the motorcycle's engine safely.
Explains how to apply the brakes effectively and safely.
Provides instructions and safety precautions for refueling the vehicle.
Lists periodic maintenance tasks and their recommended intervals.
Details how to inspect tires for cuts, damage, and tread depth.
Explains how to check and adjust tire air pressure for optimal performance and safety.
Provides step-by-step instructions for safely removing the motorcycle battery.
Guides on checking the coolant level in the expansion tank.
Guides on how to check the engine oil level correctly.
Details the process for changing engine oil and filter.
Lists possible causes and actions for a non-cranking engine.
Lists possible causes and actions for an engine that turns but doesn't start.
Lists possible causes and actions for an overheating engine.
Lists possible causes and actions for a red malfunction indicator lamp.
To Next Page
